Powerboost Function; To Cut Grass Without A Grass Catcher Or Mulch Plug Attached - Husqvarna W520i Manual Del Usuario

LED display
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To charge the multi battery
Note:
Charge the battery if it is the first time that you
use it. A new battery is only 30% charged.
1. Make sure that the battery is dry.
2. Connect the multi battery to the adapter. (Fig. 49)
3. Put the adapter in the battery charger.
4. Make sure that the green charging LED on the
battery charger comes on. That means that the
adapter and multi battery are connected correctly.
(Fig. 50)
5. When all LEDs on the battery come on and the
adapter shows 100%, the battery is fully charged.
(Fig. 51)
The adapter shows the state of charge in steps of
1%. Small deviations are possible at the start of the
charge.
6. To disconnect the battery charger from the mains
socket, pull the plug. Do not pull the cable.
7. Remove the adapter from the battery charger.
8. Remove the multi battery from the adapter.
Note:
Refer to the multi battery and battery charger
manuals for more information.
To start the product
1. Lift the battery lid.
2. Put a charged battery in battery slot number 1 below
the battery lid. For longer operation time, put a
second charged battery in battery slot number 2.
3. Disconnect the safety key from the safety key holder.
4. Push the safety key into the safety lock. (Fig. 52)
5. Stay behind the product.
6. Push the ON/OFF button on the control panel. The
display comes on.
7. Loosen the start inhibitor. (Fig. 21)
8. Push the motor brake handle in the direction of the
handlebar. (Fig. 53)
To use the drive on the wheels
• Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 54)
1484 - 005 - 23.09.2020
Charging status
50%-75%
75%-100%
Fully charged
• Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 55)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Push the SavE button (A) to start the function. The
SavE symbol (B) on the display comes on.
2. Push the SavE button again to stop the function. The
SavE symbol (B) on the display goes out. (Fig. 56)
The SavE function stops automatically if the ground
conditions make it necessary to have a higher output.
The SavE function starts automatically again when the
ground conditions let it.

PowerBoost function

When the product cuts long or wet grass, the motor
automatically increases rpm. To save battery time, the
motor goes back to standard mode automatically when
the PowerBoost function is not necessary.
To stop the product
The product stops automatically if you do not operate it
for 3 minutes.
1. Release the motor brake handle to stop the motor.
(Fig. 20)
2. Push the ON/OFF button on the control panel. All
LED lights and symbols on the display go out. (Fig.
57)
3. Remove the safety key from the safety lock and put
it in the safety key holder.
To get a good result
• Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
• Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
• Cut in different directions each time to prevent
stripes in the lawn.
To cut grass without a grass catcher or
mulch plug attached
1. Lift up the rear cover and remove the grass catcher.
2. If a mulch plug and a mulch blade are attached,
remove them.
3. Close the rear cover before you operate the product.
25