Extension Cords - Milwaukee 5455 Manual Del Operador

• Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
• Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre-
quent kickback and loss of control.
Safety Warnings Specifi c for Polishing Opera-
tions:
• Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can en-
tangle your fi ngers or snag on the workpiece.
Additional Safety Warnings
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cially designed to fi lter out microscopic particles.
Functional Description
1
2
3
4
10
9
8
7
6
1. Handle
2. Speed control dial
3. Tool rest
4. Side handle
5. Polishing pad 8. Vents
6. Rubber backing pad 9. Trigger
7. Spindle lock button 10.Cord
GROUNDING
WARNING
Improperly connecting the
grounding wire can result in the risk of
electric shock. Check with a qualifi ed electri-
cian if you are in doubt as to whether the
outlet is properly grounded. Do not modify
the plug provided with the tool. Never remove
the grounding prong from the plug. Do not
use the tool if the cord or plug is damaged. If
damaged, have it repaired by a MILWAUKEE
service facility before use. If the plug will not
fi t the outlet, have a proper outlet installed by
a qualifi ed electrician.
Grounded Tools: Tools with Three Prong Plugs
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The
plug must be connected to a properly grounded
outlet (See Figure A). If the tool should electrically
malfunction or break down, grounding provides a
low resistance path to carry electricity away from
the user, reducing the risk of electric shock.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's
grounding system and must never be attached to
an electrically "live" terminal.
Your tool must be plugged into an appropri-
ate outlet, properly installed and grounded in
accordance with all codes and ordinances.
The plug and outlet should look
like those in Figure A.
Fig. A
Double Insulated Tools:
Tools with Two Prong Plugs
Tools marked "Double Insulated" do not require
grounding. They have a special double insula-
tion system which satisfi es OSHA requirements
and complies with the applicable standards of
Underwriters Laboratories, Inc.,
the Canadian Standard Asso-
ciation and the National Elec-
trical Code. Double Insulated
tools may be used in either of
the 120 volt outlets shown in
Fig. B Fig. C
Figures B and C.
5
Specifi cations
Cat. No Load Pad
Volts RPM Diameter
No.
5455 120 AC/DC 1750 7"/9"
120 AC 0 - 1750 7"/9"
5460
5540 120 AC 0 - 2800 7"
4

EXTENSION CORDS

Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example, a 14
gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension
cord to make up the total length, be sure each cord
contains at least the minimum wire size required. If
you are using one extension cord for more than one
tool, add the nameplate amperes and use the sum
to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors,
be sure it is marked with the suffi x "W-A" ("W"
in Canada) to indicate that it is acceptable for
outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired by
a qualifi ed person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
for Extension Cords*
Extension Cord Length
Nameplate
Amperes
25'
0 - 2.0
18
2.1 - 3.4
18
3.5 - 5.0
18
5.1 - 7.0 18
7.1 - 12.0
16
12.1 - 16.0
14
16.1 - 20.0
12
* Based on limiting the line voltage drop to fi ve volts
at 150% of the rated amperes.
READ AND SAVE ALL
INSTRUCTIONS FOR FUTURE USE.
Symbology
Double Insulated
No Load Revolutions per
Minute (RPM)
Spindle Volts Alternating Current/
Direct Current
Size
Volts Alternating Current
5/8"-11
5/8"-11
Amps
5/8"-11
Underwriters Laboratories, Inc.,
United States and Canada
WARNING
always unplug tool before attaching
or removing accessories or making adjust-
ments. Use only specifi cally recommended
accessories. Others may be hazardous.
Removing and Replacing Quik-Lok
MILWAUKEE's exclusive Quik-Lok
instant fi eld replacement or substitution.
Fig. 1
1. To remove the Quik-Lok
1/4 turn to the left and pull it out.
2. To replace the Quik-Lok
tor keyways and push the connector in as far as
it will go. Turn the cord nut 1/4 turn to the right
to lock.
Polishing Pads
MILWAUKEE polishing pads are available in two
different materials. 100% lambswool pads are ideal
for compounding on non-clearcoat fi nishes. Wool/
polyester blend pads are softer, making them ac-
ceptable for clearcoat fi nishes.
Fig. 2
50' 75' 100' 150'
18 18 18 16
18 18 16 14
18 16 14 12
16 14 12 12
12
14 10
12 10
10
1. To install polishing pads, unplug the tool and
place it on its tool rest with the spindle upright.
5
ASSEMBLY
To reduce the risk of injury,
®
Cords
®
Cords provide
® Cord, turn the cord nut
® Cord, align the connec-
Disc nut
Arbor hole
Polishing
pad
Rubber
backing pad
Spindle washer
Washer fl ange
Spindle
Tool rest