Bosch MUM59 Serie Instrucciones De Uso página 24

Ocultar thumbs Ver también para MUM59 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 125
en
Operation 
Working with the continuous-
feed shredder
Figure H:
  ■ Press the Release button and 
move the swivel arm to 
position 2.
  ■ Insert the bowl: 
Tilt the bowl forwards and then set it 
down. Turn anti­clockwise until it locks 
into place.
  ■ Press the Release button and  
move the swivel arm to 
position 3.
  ■ Remove drive cover from the drive of the 
continuous­feed shredder (Fig. H-5a).
  ■ Hold disc holder at the lower end, 
ensuring that the two tips are face up.
  ■ Carefully place the required slicing 
or shredding disc onto the tips of the 
disc holder (Fig. H-6a). In the case of 
reversible discs, ensure that the required 
side is face up.
  ■ Grip disc holder at the upper end and 
insert into the housing (Fig. H-6b).
  ■ Attach the cover (note mark) and turn all 
the way in a clockwise direction.
  ■ Place continuous­feed shredder on the 
drive and rotate all the way in a clockwise 
direction, as illustrated in Fig. H-8.
  ■ Turn rotary switch to recommended 
setting.
  ■ Put food to be processed in the feed tube 
and push down with the pusher.
W Warning!
Prevent the cut ingredients from building up 
in the outlet opening.
Tip: To ensure even cutting results, process 
thin ingredients in bunches.
Note: If the food to be processed sticks in 
the continuous­feed shredder, switch food 
processor off, pull out mains plug, wait until 
the drive comes to a standstill, remove 
cover from the continuous­feed shredder 
and empty feed tube.
24 
After using the appliance
  ■ Switch off the appliance with the rotary 
switch.
  ■ Rotate the continuous­feed shredder in 
an anti­clockwise direction and remove.
  ■ Rotate the lid in an anti­clockwise 
direction and remove.
  ■ Remove disc holder with disc. To do this, 
press finger from below against the drive 
shaft (Fig. J).
  ■ Clean parts.
Blender
W Risk of injury from sharp blades /
rotating drive!
Never place fingers in the attached blender! 
Do not remove / attach the blender until 
the drive is at a standstill! Operate the 
assembled blender only and with the lid 
attached.
W Risk of scalding!
If processing hot liquids, steam escapes 
through the funnel in the lid. Add a max. 0.5
litres of hot or frothing liquid.
Warning!
Blender may be damaged. Do not process 
deep­frozen ingredients (except ice cubes). 
Do not operate blender when empty.
Working with the blender
Figure K:
  ■ Press the release button and 
move the swivel arm to 
position 4.
  ■ Remove the blender drive cover.
  ■ Attach blender jug (mark on the handle 
on mark on the base unit) and turn all the 
way in an anti­clockwise direction.
  ■ Add ingredients. 
Maximum capacity – liquid = 1.25 litres; 
maximum capacity frothing or hot liquids 
max. 0.5 litres; optimal processing 
  c apacity – solids = 50­100 g;
  ■ Attach the cover and turn anti­clockwise 
all the way into the blender handle. The 
cover must be locked in position.
  ■ Set the rotary switch to the desired 
setting.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mum59343Mum59m54Mum59m55Mum59

Tabla de contenido