Fault Codes - Husqvarna FS7000 DL Manual De Instrucciones

Ocultar thumbs Ver también para FS7000 DL:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Gearbox and blade information
Shows the recommended rpm and gear for available blade
sizes.
The tables are different depending on whether the machine is
configured for 1-Speed or 3-Speed gearbox. Select your
product model.
FS 5000 D, 1-Speed US
FS 5000 D, 1-Speed EU
FS 5000 D, 3-Speed 14-26 US
FS 5000 D, 3-Speed 20-30 US
FS 5000 D, 3-Speed 20-36 US
FS 5000 D, 3-Speed 350-650 EU
FS 5000 D, 3-Speed 500-750 EU
1
FS 5000 D, 3-Speed 500-900 EU
1 Return button (previous menu)
2 Browse to previous FS-model
3 Browse to next FS-model
4 Select button
Selected product's gearbox and blade information.
GEARBOX RANGE / BLADE RPM
2
n
n
N
1
N
+
min
min
1
[14-26, FS 50000 D]
3
Select
BLADE
BLADE
FLANGE
SIZE
SIZE
[Maximum]
GEAR
RPM
PULLEY
2
Ø
N
1
N
n
Ø
3
min
3
14"
3100
2
20"
2170
6"
4.17"
2
1
26"
1860
3
4
5
6
1 Select button
2 Return button (previous menu)
3 Gearbox range (3-speed gearbox)
4 Diamond blade diameter, inch/mm
5 Blade flange diameter, inch/mm
6 Rotational speed of diamond blade
7 Blade shaft pulley diameter, inch/mm
8 Maximum rotational speed of engine
9 Gearbox pulley diameter, inch/mm

Fault codes

Shows fault codes when the machine detects a fault.
For more information, see the "Maintenance and service"
section.
Engine
If there is no active or passive fault codes or if there is no
contact between HMI and ECU (Engine control Unit)
messages with this information will appear.
Active Engine Faults
Engine
1
Non Engine
No Active Engine Fault Codes
2
3
1 Fault codes, engine *
MENU SYSTEM
2
3
4
ENGINE
RPM
PULLEY
n
9
min
Ø
Ø
8
3000
4.51"
7
4
5
Show
Passive
Faults
6
2 Fault codes, non engine-related
3 Return button (previous menu)
4 Browse to previous fault code
5 Browse to next fault code
6 Switch between active and passive engine fault codes.
* Please see the engine Operator's Manual for more
information.
Non Engine
Non Engine Faults
Engine
E-track Motor
C1F0521
Output Current Overload
1
C1F0522
E-track Motor
Output Current Openload
I/0 Controller
U100088
Software Download Failed
Non Engine
2
3
1 Fault codes, engine
2 Fault codes, non engine-related
3 Return button (previous menu)
4 Browse to previous fault code
5 Browse to next fault code
6 Clear rectified fault code
Service Timer Menu
Settings and information of the service schedule.
5
2
3
4
Replace oil and filter
Modify
every 100 hours
Service overdue by:
23 hours
Service
Timers
Ispect radiator air filter every
50 hours
1
Time to next service:
50 hours
Check blade drive V-belt tension
every 50 hours
Time to next service:
50 hours
Lubricate front wheel bearings
every 50 hours
Time to next service:
50 hours
Replace hydraulic system filter
every 50 hours
Service overdue by:
73 hours
9
1 Button to the service mode and requires a PIN code.
2 Indication of service.
3 Indication of pop up message of service.
4 Type of service and how often it should be done.
5 The time when the next service is to be performed or the
time that has passed since the service would have been
carried out.
6 Browse to previous service message.
7 Browse to next service message.
8 Activation of pop up message for the service displayed
when the ignition is switched on.
9 Return button (previous menu)
4
5
Clear
6
6
7
Show
PopUp at
Ignition
on
8
– 31
English

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido