How To Operate The Unit - JB Systems Light LED LIGHTBAR 4TC Manual De Instrucciones

ENGLISH

HOW TO OPERATE THE UNIT

YOU CAN OPERATE THE UNIT IN 4 WAYS:
 By master/slave built-in preprogram function
 By CA-8 easy controller / CA-32F foot controller
 By universal DMX controller
 By LEDCON-02 controller
 BY MASTER/SLAVE BUILT-IN PREPROGRAM FUNCTION:
Select this function when you want an instant show. By linking the units in master/slave
connection, the first unit will control the other units to give an automatic, sound
activated, synchronized light show. Its DMX input will have nothing plugged into it, and
its master-LED will be constantly on and sound-LED will flash to the music.
Remark1: All functions should be selected on the master unit.
Remark2: A CA-8 "easy controller" can eventually be used on the master unit.
 BY CA-8 EASY CONTROLLER:
Just connect this small controller to the 1/4" jack of the master unit, and you will be able
to control the following
FUNCTIONS:
BUTTON
STANDBY
1.Synchronous strobe in
white color
2.Sound strobe in white
3.Sound strobe in
FUNCTION
rainbow colors
PS:
In this mode random
show (Sh 0) is active
Strobe select
MODE
(LED OFF)
 BY UNIVERSAL DMX CONTROLLER:
You can use any standard DMX-controller. First choose the desired DMX-channel mode and give the unit
the correct DMX start address. (see earlier to learn how this should be done)
 BY LEDCON-02 CONTROLLER:
Make sure the LED LIGHTBAR 4TC channel mode is set to "LEdC" (see earlier) and perform the
automatic address function on the LEDCON-02 before you start using the set! Further explanations and
instructions can be found in the user manual of the LEDCON-02.
JB SYSTEMS 11/64
®
OPERATION MANUAL
ACTIONS
To blackout all LED panels
Red  Green  Show1  Show2 
Blue  Yellow  ...  Show8
Cyan  Blue 
White  Color
change by sound
Color select Show select
(LED ON) (LED slow blinking)
LED LIGHTBAR 4TC
ENGLISH
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input: AC 100V - 240V, 50Hz/60Hz
Mains output (IEC-link) mains = 230Vac: daisy chain max. 10 identical units
Mains output (IEC-link) mains = 120Vac: daisy chain max. 5 identical units
Power consumption: Max. 68 Watt
Fuse: T6,3A / 250V slow blow (20mm glass)
Sound Control: Internal microphone
DMX connections: 3pin XLR male / female
DMX channels used: 1 / 4 / 7 / 12 / 16 channels
Lamp: 4x RGB 3in1 3watt LEDs (4x 4 RGB LEDs)
Size: see drawing
Weight: 7 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS 12/64
®
OPERATION MANUAL
LED LIGHTBAR 4TC