Multiplex EasyGlider PRO Instrucciones De Montaje página 11

EasyGlider PRO KIT
Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you
are completely satisfied with the contents of your kit. However, we would ask you to check all the parts (referring to the Parts List)
before you start construction, as we cannot exchange components which you have already worked on. If you find any part is
not acceptable for any reason, we will gladly correct the defect or replace the item in question once we have inspected it. Please
send the part to our Model Department, being sure to include the purchase receipt and a brief description of the fault.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents in
terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that we
cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings. Building and operating them safely
requires a certain level of technical competence and manual skill, together with discipline and a responsible attitude at
the flying field. Errors and carelessness in building and flying the model can result in serious personal injury and damage
to property. Since we, as manufacturers, have no control over the construction, maintenance and operation of our
products, we are obliged to take this opportunity to point out these hazards and to emphasise your personal
responsibility.
Additional items required for the EasyGlider PRO:
Adhesive and activator:
Use medium-viscosity cyano-acrylate glue ("cyano" - not styrofoam cyano) for this model. Epoxy adhesives produce what initially
appears to be a sound joint, but the bond is only superficial, and the hard resin breaks away from the parts under load.
Hot-melt glue (from a glue gun) is a useful alternative adhesive.
MULTIPLEX radio control system components for EasyGlider PRO:
RX-7-SYNTH receiver
alternatively
or
Micro IPD UNI receiver
alternatively
Tiny-S UNI servo (2 x required)
Nano-S UNI servo (2 x required)
Extension lead, 400 mm UNI
optional: separation filter lead, 200 mm UNI
Battery charger:
MULTIcharger LN-3008 EQU
For LiPo, LiIo and LiFe batteries with 2S or 3S cells, and NiMH and NiCd batteries with 4 to 8 cells.
EasyGlider PRO power set
Contents: Motor - Himax 2816 - 1220, speed controller- BL-27 II, 10" x 6" propeller, collet adaptor, propeller driver, spinner
EasyGlider PRO tuning power set
Inhalt:
Motor - Himax 3516 - 1130, Regler - BL -37 II, Luftschraube 12x6, Spannzange, Mitnehmer, Spinner
Flight battery Li-BATT BX-2100 mAh 2/1 2100
Li-BATT BX-2500 mAh 2/1 2500
Li-BATT BX-3200 mAh 2/1 3200
Propeller driver and spinner for EasyGlider PRO
Additional items required for the glider variant only
NiMH receiver battery, 4 / 1800 mAh
Mini switch harness with charge socket
Aero-tow release
Tools:
Scissors, balsa knife, side-cutters.
Note: remove the illustration pages from the centre of the building instructions.
Specification:
Wingspan
Overall length
All-up weight
Wing area, FAI
Wing loading
RC functions
# 21 4226
Glider
1800 mm
1110 mm
approx. 710 g
approx. 41.6 dm²
approx. 17 g / dm²
Elevator, rudder, aileron
GB
35 MHz e.g. A-band
40 MHz
35 MHz e.g. A-band
40 MHz
Elevator / rudder
2 x aileron
Aileron servo, 2 x
Aileron servo, 2 x
Order No. 15 7130
Order No. 15 7190
Order No. 15 7135
Order No. 73 3500
Electric glider
1800 mm
1110 mm
with standard power system approx. 810 g
FAI approx. 41.6 dm²
approx. 20 g / dm²
as glider, plus throttle
Order No. 5 5880
Order No. 5 5882
Order No. 5 5971
Order No. 5 5972
Order No. 6 5121
Order No. 6 5120
Order No. 8 5029
Order No. 8 5035
Order No. 9 2540
Order No. 33 2636
Best.-Nr. 33 2642
Order No. 15 6007
Order No. 8 5045
Order No. 72 3470
11