Troubleshooting Tips - Monogram ZDT165SILII Manual Del Propietário

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Problem
Start status indicator
light flashing
Dishwasher BEEPS
once every minute
Beeping at the end of
the cycle
Dishes and flatware
not clean
Spots and filming on
glasses and flatware
Cloudiness on
glassware
Suds in the tub
12
Possible Cause
The door was opened or the
cycle was interrupted.
This is a reminder that your
dishwasher door has been left
open during operation. It will
continue beeping until you
press START and close the door.
This is normal. Dishwasher will
beep at end of cycle.
Filter assembly is clogged
Low inlet water temperature
Water pressure is temporarily
low
Air gap or disposer clogged
High drain loop or air gap not
installed
Improper rack loading
Poor performing detergent
Extremely hard water
Low inlet water temperature
Overloading or improper
loading of the dishwasher
Old or damp powder detergent
Rinse agent dispenser empty
Too little or low performing
detergent
Combination of soft water and
too much detergent
Low performing phosphate-
free detergent
Water temperature entering
the dishwasher exceeds 150°F
(66°C)
Wrong detergent
Rinse agent was spilled

Troubleshooting Tips

Dishwasher
What To Do
Press the START button once and close the door within 4
seconds to start the dishwasher. Press the START button a
second time when the dishwasher is running only if you wish to
cancel the cycle.
Press START and close the door.
The dishwasher will beep (unless interupted) and the CLEAN
light will display at the end of the wash cycle.
See the Care and Cleaning section.
Make sure inlet water temperature is correct (see the Getting
Started section). Turn on the hot water faucet nearest the
dishwasher, let run until the water temperature stops rising. Then
start the dishwasher and turn off the faucet. This ensures the
entering water is hot. Select WASH TEMP - BOOST.
Turn on a faucet. Is water coming out more slowly than usual? If so,
wait until pressure is normal before using your dishwasher. Normal
water pressure to the dishwasher should be 20-120 psi.
Clean the air gap or flush the disposer.
Refer to the Installation Instructions for proper drain line
installation.
Make sure large dishware or utensils do not block the
detergent dispenser or the wash arms. See the Loading
section.
Use a highly rated detergent such as Finish
Automatic Dishwashing
Use rinse agents such as
prevent spots and prevent new film build-up.
If water is extremely hard, a softener may be required.
Make sure inlet water temperature is at least 120°F (49°C).
Load dishwasher as shown in the Loading section.
Make sure detergent is fresh.
such as Finish
Quantum
®
Detergent.
Refill with rinse agent such as
Make sure you use the proper amount of highly rated
detergent.
This is called etching and is permanent. To prevent this from
happening, use less detergent if you have soft water. Wash
glassware in the shortest cycle that will get it clean.
See A white film on glassware, dishware and the interior in
this Troubleshooting Tips section.
This could be etching. Lower the water heater temperature.
Use only automatic dishwasher detergents to avoid sudsing.
Finish
Quantum
Automatic Dishwashing Detergent
®
®
approved for use in all Monogram dishwashers.
Always wipe up rinse agent spills immediately.
Quantum
®
Detergent.
Finish
Jet-Dry
Rinse Aid
®
®
Use a highly rated detergent
Automatic Dishwashing
®
Finish
Jet-Dry
Rinse
®
®
®
to
Aid.
has been

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido