General Outline; Bulb Replacement - BFT EOS 120 VENERE D Instrucciones De Uso Y De Instalacion

ENGLISH
Thank you for buying this product, our company is sure that you will
be more than satisfied with the product's performance. The product
is supplied with a "Warning" leaflet and an " Instruction booklet
". These should both be read carefully as they provide important
information about safety, installation, operation and maintenance.
This product complies with the recognised technical standards and
safety regulations. We declare that this product is in conformity with
the following European Directives: 89/336/EEC, 73/23/EEC, 98/37/
EEC, 99/05/EEC (and subsequent amendments).

1) GENERAL OUTLINE

The EOS 120 system is compatible with the EElink protocol for fast
installation and maintenance. It is suitable for motorising sectional
doors, protruding fully retracting spring operated overhead doors and
counterweight overhead doors provided with an appropriate towing
arm. The overhead door must not be higher than 3 metres. It is easy
to install and fast to fit and does not need the door to be modified. The
irreversible gearmotor keeps the door locked in the closing position.
The control unit is builtin. It controls the operation relays and the safety
devices (photocell, rubber skirt) before performing every manoeuvre.
This product was designed to motorise the types of door men-
tioned above. Any other use is considered contrary to that
intended by the manufacturer who,therefore,cannot be held
responsible for any injuries to persons or animals,or damage
to things which might derive from misuse.
2) SAFETY
If correctly installed and used, this automation device satisfies the
required safety level standards. However, it is advisable to observe
some practical rules in order to avoid accidental problems. Before
using the automation device, carefully read the operation instruc-
tions and keep them for future reference.
• Keep children, persons and things outside the automation work-
ing area, particularly during operation.
• Keep radio control or other control devices out of children's
reach, in order to avoid any unintentional automation activation.
• Do not intentionally oppose the leaf movement.
• Do not attempt to open the door manually, if the internal locking
4 -
EOS 120 VENERE D Ver.01
USER'S MANUAL
system has not been released by pulling the appropriate wire con-
nected to the carriage (fig.1), or the external lock (SM1 or SET/S
fig.2-fig.3) activated.
• Do not modify the automation components.
• In case of malfunction, disconnect the power supply, activate the
emergency release to gain access to the automation device and
request the assistance of a qualified technician (installer).
• Before proceeding to any external cleaning operation, discon-
nect the mains powers supply.
• Keep the photocell optical components and luminous signal indi-
cation devices clean. Check that the safety devices (photocells)
are not obscured by branches or shrubs.
• For any direct assistance to the automation system, request the
assistance of a qualified technician (installer).
• Have qualified personnel check the automation system once a year.
• Check the installation frequently, in particular cables, springs and
supports to find out any unbalance, sign of wear or damage. Do
not use the operator in the case where any repairs or adjustments
are required, given that an installation malfunction or an incorrectly
balanced door could cause injuries.
• Once a month, check that the motor reverses when encountering
on obstacle 50 mm away from the floor. Should operation show
to be incorrect, request the assistance of a qualified technician,
given that an incorrect adjustment could be dangerous.
3) EMERGENCY MANOEUVRE
In case of electric power failure or system malfunction, the ma-
noeuvre must be carried out manually by pulling the wire connect-
ed to the carriage, as in fig.1. For garages which are not provided
with a second exit, it is compulsory to fit an external key release
device like Mod. SM1 (fig.2) or Mod. SET/S (fig.3).
WARNING: If the door is not correctly balanced, activation of the
carriage manual release could provoke an uncontrolled door mo-
vement.

4) BULB REPLACEMENT

To replace the courtesy light bulb, remove its transparent cover
(fig.4).
WARNING: Only 24V 25W max E14 bulbs must be used.