Parameter Menu - BFT EOS 120 VENERE D Instrucciones De Uso Y De Instalacion

The modifications made are only set if the OK key is subsequently
pressed.
When the OK key is pressed for the first time, the programming
mode is entered.
The following pieces of information appear on the display at first:
- Display Software version
- Control unit Software version
- Number of total manoeuvres carried out (the value is expressed
in thousands, therefore the display constantly shows 0000 during
the first thousand manoeuvres)
- Number of manoeuvres carried out since the latest maintenance
operation (the value is expressed in thousands, therefore the display
constantly shows 0000 during the first thousand manoeuvres).
- Number of memorised radio control devices.
When the OK key is pressed during the initial presentation phase,
the first menu (parameters, logics, radio, language, default, autosetting,
end-of-stroke adjustment) can be accessed directly. ) can be accessed directly.
Here follows a list of the main menus and the respective submenus
available.
The predefined parameter is shown between square brackets [ 0 ].
The writing appearing on the display is indicated between round
brackets.
Refer to Figures A and B for the control unit configuration proce-
dure.

8.2) Parameter Menu (

- Automatic Closing Time ( Automatic Closing Time ( (
Set the numerical value of the automatic closing time from 1 to Set the numerical value of the automatic closing time from 1 to
180 seconds.
- Opening torque ( Opening torque (
value between 1% and 99%.
- Closing torque ( Closing torque (
Set the motor torque value between 1% and 99%. Set the motor torque value between 1% and 99%.
WARNING: Check that the impact force value measured at
the points established by the EN 12445 standard is lower
than that specified in the EN 12453 standard.
Incorrect sensitivity setting can cause injuries to persons or
animals, or damage to things.
- Partial opening (
Set the numerical value for partial opening from 10 cm (000,1)
to 6 m. (006.0).
- Zone ( ) [ 0 ]
Set the zone number between a minimum value of 0 and a maxi-
mum value of 127. See paragraph 11 on "Serial connection".
8.3) Menu Logiche (
- TCA ( ) [ OFF ]
ON Activates automatic closing
OFF Excludes automatic closing
- 3 Steps ( ) [ OFF ]
ON Enables 3-step logic. A start impulse has the following ef-
fects:
door closed:..................................................................opens
on opening: .................stops and enters TCA (if configured)
door open: ................................................................... closes
on closing: ............................. stops and reverses movement
after stopping:...............................................................opens
OFF Disables 3-step logic.
- Opening Impulse lock (
ON The Start impulse has no effect during the opening phase.
OFF The Start impulse becomes effective during the opening
phase.
- Pre alarm ( ) [ OFF ]
ON The blinker comes on about 3 seconds before the motor
starts.
OFF The blinker comes on at the same time as the motor starts.
- Photocells on opening (
ON: In case of obscuring, this excludes photocell operation on
opening. During the closing phase, it immediately reverses
the motion.
INSTALLATION MANUAL
)
) [ 40s ]
) [ 50% ] Set the motor torque
) [ 50% ] [ 50% ]
) [1,0 m]
)
) [ OFF ]
) [ OFF ]
OFF: In case of obscuring, the photocells are active both on
opening and on closing. When a photocell is obscured on
closing, it reverses the motion only after the photocell is
disengaged.
- Photocell test (
ON: Activates photocell check (see fig. 17A)
OFF: Deactivates photocell check
- Gate-open or 2nd radio channel warning light (
ON: The output between terminals 14 and 15 is configured as
Gate-open warning light, in this case the 2nd radio channel
controls pedestrian opening.
OFF: The output between terminals 14 and 15 is configured as 2nd
radio channel.
- Fixed code (
ON: The receiver is configured for operation in fixed-code mode,
see paragraph on "Radio Transmitter Cloning".
OFF: The receiver is configured for operation in rolling-code mode,
see paragraph on "Radio Transmitter Cloning".
- Radio transmitter programming (
ON: This enables transmitter storage via radio:
1 – First press the hidden key (P1) and then the normal key (T1,
T2, T3 or T4) of a transmitter already memorised in standard
mode by means of the radio menu.
2 – Within 10s press the hidden key (P1) and the normal key
(T1, T2, T3 or T4) of a transmitter to be memorised.
The receiver exits the programming mode after 10s, other new
transmitters can be entered before the end of this time.
This mode does not require access to the control pan-
el.
OFF: This disables transmitter storage via radio.
The transmitters can only be memorised using the appropriate
Radio menu.
- Start-Open selection (
ON: The input between the two terminals 3-4 acts as open.
OFF: The input between the two terminals 3-4 acts as start.
- PED-CLOSE selection (
ON: The input between the two terminals 16-17 works as CLOSE.
OFF: The input between the two terminals 16 and 17 works as
PARTIAL OPENING.
- Master/Slave (
ON: The control panel is set as Master in a centralised connec-
tion.
OFF: The control panel is set as Slave in a centralised connec-
tion.
8.4) Radio Menu (
- Add
Allows you to add one key of a radio control device to the receiver
memory; after storage it displays a message showing the receiver
number in the memory location (from 01 to 64).
- Add Start button (
associates the required key to Start command
- Add 2ch button (
associates the required key to 2nd radio channel
For transmitters with hidden key, press hidden key P1 (fig. B1A). For
transmitters without hidden key, the key P1 function corresponds
to simultaneously pressing the 4 transmitter keys or, after opening
the battery compartment, bridging the two P1 points by means of
a screwdriver (fig. B1A).
- Read ( )
Checks one key of a receiver; if stored it displays a message
showing the receiver number in the memory location (from 01 to
64), and the key number (T1, T2, T3 or T4).
- Delete ( )
Removes one single key of a transmitter from the receiver memory;
after deletion it displays a message showing the receiver number
in the memory location (from 01 to 64).
- Eliminate list (
WARNING! Completely removes all memorised radio control devices
from the receiver memory.
ENGLISH
) [ OFF ]
) [ OFF ]
) [ ON ]
) [ OFF ]
) [ OFF ]
) [ OFF ]
)
)
)
)
EOS 120 VENERE D Ver.01 -
) [ ON ]
19