General Warnings; General Description; Fuels; Safety Devices - Bio Bronpi Berta Instrucciones De Instalación, Uso Y Mantenimiento

1

GENERAL WARNINGS

The installation of the stove must be done according to the local, national or European regulations.
Stoves by Bronpi Calefacción, S.L. are manufactured under a quality control system in order to protect both the user and the fitter in the
event of possible accidents. We also recommend to the authorized installer that, each time an operation in the stove is going to be done,
pay special attention to the electrical connections, especially that stripped or bear wires are never left outside the connections, avoiding
dangerous contacts.
The installation must be performed by authorized personnel who must provide the buyer a declaration of conformity of the
installation where he will assume full responsibility for the final installation and, therefore, the proper operation of the installed
product. Bronpi Calefacción S.L. will not assume any liability in the case of failure complying with these precautions.
The manufacturer will not assume any liability for damages caused to third parties due to improper installation or misuse of the stove.
In order to ensure the correct operation of the product, components can only be replaced with original spare parts and by an authorized
technician.
Maintenance of the stove must be performed at least once a year by an Authorized Technical Service.
For more security you should consider:
• Do not touch the stove with bare feet or with wet body parts.
• The door of the machine must be closed during operation.
• It is forbidden to modify the safety or regulating devices without the permission of the manufacturer.
• Avoid direct contact with any parts of the product that tend to reach high temperatures during its operation.
2

GENERAL DESCRIPTION

The stove that you have purchased contains the following pieces:
• Complete structure of the stove on the pallet.
• Inside the combustion chamber you can find: a box/bag with a thermal glove that allows us to use the handle of the door and other
components. The electrical interconnection cable between the stove and the electrical network. A hook (cold hands handle) to make
easier the removing and cleaning of the burner. A yellow leaflet with the most important warnings and considerations. A book in order
to register all maintenance tasks performed to the stove as well as this installation, use and servicing manual.
• Inside the combustion chamber you will also find the burner and the ash pan.
The equipment consists of several elements of steel sheets welded, with different thickness and pieces vermiculite. It also has a door with
vitro ceramic glass (resistant up to 750ºC) and ceramic rope seal for the integrity of the combustion chamber.
Heating is produced by:
a. Forced convection: thanks to the fan placed on the bottom of the stove, the air at room temperature is aspired and it is returned to the
room at a higher temperature.
b. Radiation: through the vitro ceramic glass and the body the heat is irradiated towards the environment.
3

FUELS

WARNING:
The use of a low quality pellet or any other fuel in disagreement with the specifications mentioned below implies the cancellation of
the warranty and the responsibility bounded to the product
Only wood pellets certified by these standards or certifications should be used :
Standards:
• Ö-Norm M 7135 | Din 51731 | EN-14962-2 (all repealed and included in ISO-17225-2)
• ISO-17225-2
Quality certifications:
• DIN+
• ENplus: On the web site (www.pelletenplus.es) you can check all manufacturers and distributors with certificate.
It is strongly recommended that the pellet is certified with quality certifications because this is the only way to guarantee the
constant quality of the pellet.
Bronpi Calefacción recommends the use of pellets with 6 mm diameter, a maximum longer of 3.5 cm and with a humidity percentage lower
than 8%.
• STORAGE OF PELLET
In order to guarantee combustion without any problem it is necessary to keep the pellet in a dry ambient.
• PELLET SUPPLY
Open the tank cover on the top of the equipment and empty directly the pellet bag taking care of not overflowing.
4

SAFETY DEVICES

• SMOKE EXTRACTOR FAN BREAKDOWN
If the extractor fan stops, the electronic card automatically blocks the fuel supply.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS 14 MOD. BERTA