Pioneer BDP-440 Manual De Instrucciones página 57

BDP-140_UCXCNSM_IBD_EN.book Page 57 Tuesday, July 19, 2011 10:54 AM
Problem Check
• No sound is output. Is the disc played back in
slow motion?
• Sound is not output
properly. Is the disc played back in fast
forward or fast reverse?
Are the audio cables properly
connected?
Is the audio cable damaged? If the cable is damaged, replace it with a new one.
Are the connected
components (AV receiver or
amplifier, etc.) properly set?
Are you trying to listen to the
sound of the HDMI OUT
terminal while watching the
picture from the VIDEO
output terminals?
Is HDMI Audio Out properly
set?
Is a DVI device connected?
Multi-channel sound is not Is the audio output of the
output. connected AV receiver or
amplifier, etc., properly set?
Is multi-channel sound
selected?
Noise can be heard when Is the connected AV receiver
outputting DTS Digital Audio or amplifier compatible with
signals from the DIGITAL DTS Digital Surround?
OUT terminal.
192 kHz or 96 kHz digital
audio signals cannot be
output from the DIGITAL
OUT terminal.
Secondary audio or Is HDMI Audio Out properly
interactive audio is not set?
output.
Are Digital Output properly
set?
Sound is fast or slow. When an HDMI cable is
connected, are audio signals
(Only for BDP-440)
being output from devices
connected with cables other
than HDMI cables?
After a disc is inserted, Are there too many files
Loading stays displayed and
recorded on the disc?
playback does not start.
 is displayed in file names,
etc.
A message indicating low
memory appears while
playing a BD-ROM disc.
Remedy
No sound is output during slow motion play and forward and reverse
scanning.
• Connect the cable properly according to the connected devices
(page 16).
• Insert the cable firmly and all the way in.
Read the operating instructions for the connected components and
check the volume, input, speaker settings, etc.
Audio signals are not output from the HDMI OUT terminal when video
signals are being output from the VIDEO output terminals. When
watching the picture of the VIDEO output terminals, connect an optical
digital audio cable or regular audio cables to listen to the sound
(page 20). Once connections are completed, use Setup Navigator to
make the player's settings (page 24).
Set HDMI Audio Out to Auto or PCM. (page 41).
The sound will not be output from the HDMI OUT terminal if a DVI
device is connected. Connect the device to a DIGITAL OUT terminal or
the AUDIO OUT terminals (page 20).
For some BDs, audio signals are only output from DIGITAL OUT
terminal or the HDMI OUT terminal.
Read the operating instructions for the connected AV receiver or
amplifier and check the audio output settings of the AV receiver or
amplifier.
Use the menu screen or AUDIO to switch the disc's sound to multi-
channel.
If an AV receiver or amplifier that is not compatible with DTS Digital
Surround is connected to the DIGITAL OUT terminal, set Digital
Output to PCM (page 41).
It is not possible to output 192 kHz or 96 kHz digital audio signals from
this player's DIGITAL OUT terminal. The signals are automatically
converted to 48 kHz or less for output.
When listening to the sound from an HDMI OUT terminal, set HDMI
Audio Out to PCM (page 41).
When listening to the sound from an DIGITAL OUT terminal, set
Digital Output to Re-encode or PCM (page 41).
When a Pioneer AV receiver or amplifier compatible with the PQLS
function is connected directly to the player's HDMI OUT terminal using
an HDMI cable, the PQLS function is activated when playing an audio
CD (CD-DA). Because of this, the sound output from components other
than the ones connected by an HDMI cable may be fast or slow. If this
happens, set Control to Off (page 41).
When a disc on which files are recorded is inserted, depending on the
number of files recorded on the disc, loading may take several dozen
minutes.
The characters that cannot be displayed on this player are displayed in
.
• Connect a USB memory device (page 21).
• Erase the data stored on the connected USB memory device from
BUDA Setup (page 45).
08
57
En