Setting The Ip Address - Pioneer BDP-440 Manual De Instrucciones

Ocultar thumbs Ver también para BDP-440:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

BDP-140_UCXCNSM_IBD_EN.book Page 44 Tuesday, July 19, 2011 10:54 AM
 Setting the IP address
07
Select and set Network  IP setting  Next
1
Screen.
Use / to select, then press ENTER.
2
Set IP address.
Use /// to set the IP address of the player or DNS
server, then press ENTER.
• Auto Set IP Address
On – The player's IP address is obtained
automatically. Select this when using a broadband
router or broadband modem that has a DHCP
(Dynamic Host Configuration Protocol) server
function. This player's IP address will automatically
be allocated from the DHCP server.
Off – The player's IP address must be set manually.
Use the number buttons (0 to 9) to input the IP
address, subnet mask and default gateway.
• Auto Set DNS Server Address
On – The DNS server's IP address is obtained
automatically.
Off – The DNS server's IP address must be set
manually. Use the number buttons (0 to 9) to input the
DNS server's IP address stipulated by your Internet
service provider.
Note
• When Auto Set IP Address is set to Off, Auto Set
DNS Server Address is also set to Off.
• For information on the DHCP server function, refer to
the operating instructions for the network device.
• You may need to contact your Internet service
provider or network administrator when inputting the
IP address manually.
 Setting the proxy server
Only set the proxy server if so instructed by your Internet
service provider.
Select and set Network  Proxy Server  Next
1
Screen.
Use / to select, then press ENTER.
2
Select and set Use or Not use at Proxy Server.
Use / to change, then press .
• Use – Select this when using a proxy server.
• Not use – Select this when not using a proxy server.
If you have selected Use, proceed to step 3.
3
Select and set Server Select Method.
Use / to change, then press .
• IP Address – Input the IP address.
• Server Name – Input the server name.
44
En
4
Input IP Address or Server Name.
Use the number buttons (0 to 9) to input the number if you
select IP address in step 3. Use / to move the cursor.
Use the number buttons (0 to 9) to input characters if you
select Server Name in step 3.
The characters that can be input for the server name are
listed on the table below. Pressing a button repeatedly
cycles through the characters shown.
• If you want to enter two characters in succession that
are both on the same button (for example a P and an
R), press  after inputting the first character then
input the second character.
• Use CLEAR to delete the last character.
• Use / to move the displayed characters when all
the input characters cannot be displayed.
Key
Characters
Key
1
1. –
6
2
a b c 2
7
3
d e f 3
8
4
g h i 4
9
5
j k l 5
0
5
Input Port Number.
Press , then use the number buttons (0 to 9) to input
the number.
6
Press ENTER to set.
 Displaying the network settings
 Select and set Network  Information  Next
Screen.
Use / to select, then press ENTER.
The MAC address, IP address, subnet mask, default
gateway and DNS server (primary and secondary)
settings are displayed.
When Auto Set IP Address is set to On, the values
obtained automatically are displayed.
Note
• "0.0.0.0" is displayed when each IP address has not
been set.
 Testing the network connection
 Select and set Network  Connection Test 
Start.
Use / to select, then press ENTER.
"Network connection test completed successfully." is
displayed once the test is completed. If any other
message is displayed, check the connections and/or
settings (page 22).
Characters
m n o 6
p q r s 7
t u v 8
w x y z 9
0

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Bdp-140

Tabla de contenido