Work Pro Digiline Serie Manual De Usuario página 3

Additional notes about Security and Maintenance
- Before connecting the supply, check if the local voltage is matched as value marked in the rear side of the unit.
- Protect the cable to be pinched or stepped, particularly in connector, socket or where the cable out of the unit.
- Contact with your dealer in case of table replacement.
- If the fuse blows, replace it by another fuse with the same dimensions and rate. If it blows again, do not replace it and contact with
your dealer in order to check the unit.
- To disconnect the unit catch from the socket, never pull the cable, it can cause its breakage and produce electric shocks.
For the servicing or maintenance of the unit, contact with your dealer. This process must be done by qualified personnel.
1. DIGILINE DEVICES
1.1. Introduction
Digiline MX MKII by itself is exclusively dedicated to processing uses, it means it doesn´t include amplifier. In only 1 HU 19" rack
unit, it is a very interesting alternative for those who already have a power amplifier or for others who need more power at the
outputs.
The remote control can be operated through ASCII orders by RS 232 or TCP/IP. Thus, it is possible to program automatic actions
like preset changes, mute for all channels except one, etc. It also features 12 GPIO inputs/outputs, providing further configuration
possibilities.
Digiline MX MKII features a RS232 port in order to receive ASCII orders from external devices that use this protocol. It is possible
to program automatic actions like preset changes, mute for all channel except one, etc.
WorkCAD Designer,
1.2. Specifications
Technical data
Outputs:
Control interface:
Control connections:
Control software:
Control indicators:
Frontal controls:
GPI inputs:
Input sensitivity:
Phantom supply:
Matrix mixer:
Crossover:
Equalizer:
Dynamic control:
Output channel volume control:
Presets memory:
DSP Architecture:
Oversampling:
Digital De-emphasis:
Power requirement:
Main supply:
Dimensions (WxHxD):
THE UNIT MUST BE EARTHED
By security reasons and in order to avoid electric shocks, the main supply
cable has a ground terminal. This pin MUST NOT BE REMOVED.
If the connections socket has not the adequate pin, contact with an
electrician in order to change the obsolete socket.
Con guration software available to download at www.workpro.es
Inputs: 8 double MIC inputs (with phantom) + LINE balanced and one additional MIC input. All of them have Euroblock connector.
RJ45 (Ethernet TCP/IP) , DB9 (RS232) and Euroblock (GPI).
Frontal LEDs for signal presence, input & output clip.
THD+N:
8 mixers of 8 channels with reverse signal and mute for any channel.
Butterworth type fi lters, Linkwitz-Riley and Bessel up to 4° order with up to 7 filters per output.
Equalizations with peak type curves, low pass, high pass, notch, low shelving, high shelving and band pass with up to 7 fi lter
per output maximum.
Common Limiter compressor for f irst 7 channels and an independent one for the last one.
Selectable by software and frontal potentiometer (36 dB to -109 dB range). 48 bit processing architecture with 76 bits of
precision for most audio processing features.
10 program memories available.
32 bit processing with 40 bits of precision.
8 x Oversampling with fi fth order noise shaping @ 32-48 kHz; 4 x Oversampling @ 88.2 and 96 kHz; 2 x Oversampling @
176.2 kHz and 192 kHz.
For 32,44.1 and 48 kHz.
Digiline MX
. 8 outputs with Euroblock connector
TCP/IP, RS232 and GPI.
WorkCAD designer (Software available to download at www.workpro.es)
------------
12 GPI (TTL inputs software selectable).
0 dBu (20 dB PAD).
15 V MIC inputs (selectable).
< 0.1 %.
DSP features
Physical Features
50 W .
AC 90-264 V (automatic).
483 x 44 x 229 mm.
PAGE 02