Sound Menu - Yamaha YSP-1 Manual De Instrucciones

MANUAL SETUP

SOUND MENU

Use to manually adjust any speaker setting or compensate
for video signal processing delays.
(SET MENU → MANUAL SETUP →
SOUND MENU)
1 SOUND MENU 1/2
. A)SUBWOOFER SET
B)SPEAKER LEVEL
C)DYNAMIC RANGE
D)AUDIO SET
[ ]/[ ]:Up/Down
[SELECT]:Enter
SUBWOOFER SET (Subwoofer set)
Use to manually adjust subwoofer settings.
A)SUBWOOFER SET
. BASS OUT;;;;;;BOTH
CROSS OVER;;;100Hz
LFE LEVEL;;;;;;0dB
DISTANCE;;;;;;3.0m
[ ]/[ ]:Up/Down
[<]/[>]:Select
BASS OUT (Bass out)
Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right speaker positions.
This setting also determines the routing of LFE (low-
frequency effect) signals found in Dolby Digital or DTS
sources.
Choices: SWFR (subwoofer), FRONT, BOTH
Initial setting: BOTH
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer according to the speaker settings.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front speakers according to the speaker settings
(even if you have previously set the front speakers to
SMALL).
• Select BOTH if you connect a subwoofer and you want
to output low-frequency signals from front channels to
both the front speakers and subwoofer. LFE and low-
frequency signals from other channels are also directed
to the subwoofer according to the speaker settings. Use
this function to reinforce low-frequency signals using
the subwoofer when playing back sources such as CDs.
38
CROSS OVER (Cross over)
When BASS OUT is set to SWFR, you can use this
feature to select a cross-over (cut-off) frequency for all
low-frequency signals. All frequencies below the selected
frequency will be sent to the subwoofer speaker position.
Choices: 80Hz, 100Hz, 120Hz
LFE LEVEL (Low-frequency effect level)
Select to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer. The LFE channel carries low-frequency
special effects which are only added to certain scenes.
This setting is effective only when this unit decodes Dolby
Digital or DTS signals.
Choices: –20 to 0 dB
DISTANCE (Distance)
Select to adjust the distance of the subwoofer from the
listening position.
Choices: 0.3 to 15.0 m
Initial setting: 3.0 m
SPEAKER LEVEL (Speaker level)
You can manually balance the speaker levels between the
front left or surround left speakers and each speaker
selected.
When setting the front right, center or surround left
speakers or the subwoofer, the test tone is output from the
front left speakers and the selected speaker position.
When setting the surround right speaker, the test tone is
output alternately from the surround left and right
speakers.
When PARAMETER is adjusted in EASY SETUP or
MANUAL SETUP, the factory default value is
automatically set for this parameter.
Depending on beam mode settings, some channels may
not be available for selection.
In this case, "NONE" is displayed.
B)SPEAKER LEVEL 1/2
-
.
FR
C
SL
*OUT : FL )FR
*MODE: 5 BEAM
[ ]/[ ]:Up/Down
[<]/[>]:Select
• FR adjusts the balance of the front left and front right
speakers.
• C adjusts the balance of the front left and center
speakers.
• SL adjusts the balance of the front left and surround
left speakers.
• SR adjusts the balance of the surround left and
surround right speakers.
• SWFR adjusts the balance of the front left speaker and
subwoofer.
+