Technical Data; Double Insulation; Additional Handle - Narex EV 16 K-S Instrucciones De Uso

Technical data

Drill
Type
Supply voltage (V)
Power frequency (Hz)
Power input (W)
Speed under load (rpm)
1st speed gear
2nd speed gear
Idle speed (rpm)
1st speed gear
2nd speed gear
Maximum torque (Nm)
1st speed gear
2nd speed gear
Speed pre-selection
Right-left turning
Extent of chuck dia. (mm)
Thread on spindle
Drilling dia. max (mm)
into steel
into aluminium
into wood
Clamping neck dia. (mm)
Weight (kg)
Protection class
Controls
1 ...........Chuck with ring gear
2 ...........Clamping neck
3 ...........Latching pin (EV 16 K-2S)
4 ...........Switch / controller
5 ...........Alteration switch lever
6 ...........Speed pre-selection wheel
7 ...........Air vents
8 ...........Gear-shifting lever

9 ...........Additional handle

10 .........Stop bar
11 .........Chuck hook
12 .........Spots on spindle
13 .........Spanner
14 .........Wing screw
15 .........Wing screw
16 .........Wing screw
The displayed or described accessories need not be included in the
delivery package.

Double insulation

To ensure maximum safety of the user, our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 50114.
Use
The machine is intended drilling in wood, metal, ceramic and plas-
tic. Machines with electronic control and right/left rotation are also
suitable for screwing and thread cutting (only for soft screwdriving
applications).
The user alone is responsible for any liabilities caused by usage
other than intended.
EV 16 K-S EV 16 K-2S
230–240 230–240
50–60 50–60
1 100 1 100
0–400 0–630
0–1 125
û
0–650 0–1 000
0–1 800
û
98 62
35
û
ü ü
ü ü
3–16 3–16
5/8"-16UN-2A 5/8"-16UN-2A
20 20
28 28
65 50
57 57
3.4 4.0
II / II /
Commissioning and use
Any unauthorised use might cause damage to the tool. Therefore
follow these instructions:
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or
stoppage.
- Always change the speed gear when the machine is idle or at
the machine slow-down at low speed, in no case during the
drilling or when the machine is otherwise loaded.
Check whether the data on the rating plate match with the real
power supply voltage. The tool intended for 230 V~ may be also
connected to 220/240 V~. Check whether the plug type corre-
sponds to the socket type.
Attention! Prior to handling the accessories, the pow-
er supply cable has always to be disconnected from
the power source socket!
Additional handle
For safety reasons always use the enclosed auxiliary handle (9).
Fasten the auxiliary handle to the clamping collar (2) with the wing
bolt (14).
By loosening the wing bolt (15) the drilling depth can be adjusted
with the depth stop adjustment (10).
The auxiliary handle is used to guide the machine securely, espe-
cially with sudden occuring reaction torque (e. g. jamming of the
drill bit).
By loosening the wing bolt (16) the position of the auxiliary
handle can be adjusted in length direction.
Apply the pressure required for work against the han-
dle only and not against the auxiliary handle (9).
Clamping a drill
Insert tool and tighten equally in all 3 holes with chuck key.
Switching on and off
By pressing the switch button (4a) the machine activates and re-
leasing the button stops it.
English
13