IMG STAGELINE RGBL-430DMX Manual De Instrucciones página 16

7.1.1 Overview of individual menu items
GB
Automatic show programs
1
PROGRAM
P:01S:01
Select the program (
S:01
speed ( ...
lower the program speed. With the setting
the program selected will not start.
Music-controlled show programs
2
SOUND
M:1 S:31
SOUND
In the mode
picked up by an internal microphone. Select the
M:1
program ( ...
S:01 31
( ... ): The higher the value, the higher the
sensitivity to sound. With the setting
gram selected will not start.
Cooling mode
3
COOLMODE
REGULATE
REGULATE
The total brightness (menu item
can be set to 100 % max. When the temperature
exceeds 48 °C, the fans will start. When the
temperature exceeds 60 °C, the LEDs will be
dimmed in addition.
POWER
The total brightness (menu item
can be set to 100 % max. The fans will operate
continuously. When the temperature exceeds
70 °C, the LEDs will be dimmed.
STUDIO
The total brightness (menu item
can be set to 80 % max. When the temperature
exceeds 70 °C, the fans will start and the LEDs
will be dimmed.
Operation with a DMX controller or
4
operation as a slave unit
DMXSETUP
M:1A:001
For operation with a DMX controller, select the
desired channel mode (number of DMX control
channels). Six channel modes are available:
16
P:01 ... 16
). Then set the
31
): The higher the value, the
, the unit will respond to sound
3
). Then adjust the sensitivity
S:00
SETUPDIM
SETUPDIM
SETUPDIM
M:1
= 1-channel mode
M:2
= 3-channel mode
M:3
= 7-channel mode
M:4
= 12-channel mode
M:5
= 11-channel mode
M:6
= 25-channel mode
The number of DMX channels depends on the
functions required and may also depend on the
S:00
,
number of control channels available on the light
controller. The functions available in the six chan-
nel modes can be found in chapter 9.
Then set the DMX start address (
For separate control of all DMX-controlled units,
each unit must have its own start address. Exam-
ple: If the first DMX channel of the RGBL-430DMX
is to be controlled by the DMX controller via DMX
address 17, set the start address on the RGBL-
430DMX to 17. All other DMX channels of the
RGBL-430DMX will be automatically assigned to
, the pro-
the subsequent addresses.
Example: When the 7-channel mode is adjusted and the
start address is 17, the channels 1 to 7 will be assigned
to the addresses 17 to 23. Address 24 will be the next
possible start address available for the subsequent
DMX-controlled unit.
For operation as a slave unit (
select the setting
M:1 M:6
...
)
...
5 9
COLORSET
100% RED
)
red
COLORSET
100% WHI
white
)
The brightness of red, green, blue, white and
amber can be separately adjusted from 0 – 100 %.
Note: The settings of these menu items will affect all oper-
ating modes (
tings, however, will only apply to this unit; they will not
apply to any slave units connected.
For operation without DMX controller, these menu
items can be used to set the light effect unit to a
desired lighting colour. For DMX control, these
menu items can be used to correct the colour bal-
ance; thus, the lighting colour of the unit can be
matched to the lighting colour of other units when
different light effect units are used.
SLAVE
instead of the setting
.
Brightness of
red, green, blue, white, amber
COLORSET
100% GRE
green
COLORSET
100% AMB
amber
PROGRAM SOUND
, and DMX mode). The set-
A:001 512
... ) .
chapter 5.2),
COLORSET
100% BLU
blue