Please unfold page 3. Then you can always see the
GB
operating elements and connections described.
1 Operating Elements and Connections
(fig. 3)
1 Cold appliance chassis plug for mains connection
(230 V~/50 Hz)
2 Fuse; replace a burnt-out fuse by one of the same
type only
3 Microphone
4 Mounting bracket
5 Setcrews
2 Safety Notes
This unit corresponds to the directive for electromag-
netic compatibility 89/336/EEC and to the low voltage
directive 73/23/EEC.
Please observe the following items in any case:
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
The unit heats up very much during operation. To
prevent burning yourself, never touch the housing
during operation; let the unit cool down for a few
minutes after switching off before you touch it.
The heat generated within the unit must be carried
off by air circulation. Therefore, do not cover the air
vents of the housing.
Do not insert anything into the air vents! This may
result in an electric shock.
Do not operate the unit or immediately disconnect
the plug from the mains socket
1. if there is visible damage to the unit or to the
mains cable,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
Attention!
The unit is supplied with hazardous mains voltage
(230 V~). Inexpert handling may cause an electric
shock hazard. In any case the unit must be re-
paired by skilled personnel.
Never pull the mains cable for disconnecting the
mains plug from the socket.
For cleaning only use a dry, soft cloth; never use
chemicals or water.
No liability for any damage will be accepted if the
unit is used for other purposes than originally in-
tended, if it is not correctly installed or operated or
not repaired in an expert way.
If the unit is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
6
Important for U. K. Customers!
The wires in this mains lead are coloured in accord-
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning - This appliance must be earthed.
3 Applications
The light effect units LE-560 and LE-570 are ideally
suited for stage and disco applications. The units pro-
ject various multicoloured geometric patterns via a
rotating mirror (model LE-560: two-piece mirror, model
LE-570: three-piece mirror) and thus provide an ideal
dance floor atmosphere. Light control is made via an
integrated microphone.
3.1 Functioning
Via the built-in microphone (3), the multicoloured pat-
terns (gobos), the sense of rotation, and the rotating
speed of the mirror are controlled by the ambient noise
(mainly by low-frequency sound). An existing music
system must be controlled to such a volume that the
coloured patterns change and move to the rhythm of
the music. Without any ambient noise, the unit controls
the gobos and the mirror at random.
4 Inserting a Lamp
The light effect unit is supplied without lamp. A halogen
lamp 15 V/150 W with a GZ 6.35 lamp base (e. g.
HLO-15/150MR available from "img Stage Line") is
required.
Never use a lamp with a wattage higher than
150 W!
Important!
Always disconnect the mains plug before inserting or
removing the halogen lamp! As the halogen lamp
heats up very much during operation, let it cool down
after operation of the unit (minimum cooling time
5 minutes) before replacing it.
1) Unscrew the two black screws on the lower side of
the housing and open the cover of the lamp com-
partment.
,