Safety Instructions For All Operations - Black and Decker PRO Serie Manual De Instrucciones

c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
FEATURES (FIG. A)
1. Slider switch
2. Cord
3. Tool free guard
4. Side handle (3 positions)
5. Spindle lock button
Safety warnings common for grinding, sanding,
wire brushing or abrasive
a. This power tool is intended to function as a
grinder, wire brush, sander or cut-off tool . Read
all safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury. Operations
such as polishing are not recommended to be
performed with this power tool. Operations for which
the power tool was not designed may create a hazard
and cause personal injury.
b. Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
c. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
e. The arbor size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle
of the power tool. Accessories with arbor holes that
do not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
f. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive wheel
for chips and cracks, backing pad for cracks, tear
Construction
or excess wear, wire brush for loose or cracked
Earthing
wires. If power tool or accessory is dropped,
Terminal
inspect for damage or install an undamaged
Safety Alert
accessory. After inspecting and installing an
Symbol
accessory, position yourself and bystanders away
Revolutions
or Recipro-
from the plane of the rotating accessory and run
cation per
minute
the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
g. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
ENGLISH • 17
SAFETy INSTRUCTIONS
FOR ALL OPERATIONS