Creating User-Defined Show Programs - IMG STAGELINE ODB-1212RGBW Manual De Instrucciones

b) The colours red (
B W
( ) and white ( ) can be selected one
after the other with the button
To change the brightness of a colour,
press the button
was selected. The arrow
cede the brightness value (e. g.
R:Ɗ255
). Now change the bright-
ness with the button
c) Press the button M: The arrow will
precede the colour indication again
ƊR:219
(e. g. ). The next colour can
be selected.
d) When the desired shade of white or
shade of colour has been set, press
the button M repeatedly until the
number of the shade of white
appears again (e. g.
ting will be saved.
e) All values you may have changed
can be reset to their factory settings
(chapter 4.5.1).
COLOUR
01
52 unchangeable colours
↵
1) Press the button
ing. Select the colour with the button
M
or .
2) Confirm the setting with the button
The indication will stop flashing.
SETUPDIM
Set the brightness for all
255% MAX
operating modes
1) Press the button
value will start flashing. Set the bright-
ness with the button
2) Confirm the setting with the button
The indication will stop flashing.
L
3) Use the button M,
operating mode desired.
4.2 Creating user-defined
show programs
It is possible to create 12 different show
programs with up to 32 individual light
scenes each:
1) Select the menu item
L
the button M, or
up this menu item with the menu item
CUSTOM
that is used to execute the
user-defined programs (chapter 4.1).
↵
2) Press the button
CUSTOM12
ƊPro01
will appear on the display.
Show program 1 is selected. All further
steps are shown in figure 4.
3) To copy the user-defined programs to
other ODB-1212RGBW:
Select the menu item
press the button
appear on the second line. Press the
M
button sequence
word and then press the button
again.
12
R G
), green ( ), blue
L M
or .
↵
after the colour
Ɗ
will pre-
L M
or .
ƊW03
): The set-
01
: will start flash-
L
↵
.
↵
: The brightness
L M
or .
↵
.
M
or to return to the
CUSTOM12
with
M
. Please do not mix
:
UPLOAD
and
↵
PASSWORD
. will
L M L
, , , as a pass-
↵
RESET
ENTER
UPDATE
+/-: 00
PCB TEMP
039
DOWNLOAD
VERSION
1-20-05H
SETUPCUR
LINE
MASTER
ON
KEY LOCK
OFF
SETUPDIS
ON
RUN MODE
DMX
DMX SIGN
FREEZE
UPLOAD
CUSTOM12
COLOUR
01
SETUP ID
OFF
WHITE 11
W01
SETUPDIM
255% MAX
COLORSET
255% RED
DMXSETUP
CH59A001
CUSTOM
button M
01
L
or button
M
button
PROGRAM
P:01S:01
Ž
Main menu
To reset values to their factory settings
For service only
To indicate the internal temperature
The LEDs will be dimmed when 65 °C
are exceeded.
Without function
To indicate the firmware version
Without function
To output the control signal for the slave units
Key lock
Display: ON = constantly switched on
OFF = switched off approx. after 20 sec-
onds when no button is pressed
Mode DMX or SLAVE; the setting will have no
effect on the standalone mode
Behaviour of the unit in case of control signal
loss
To transfer user-defined show programs to
other ODB-1212RGBW
To create 12 user-defined show programs
To select 52 predefined, unchangeable colours
To use subaddresses
To select 11 predefined shades of white; user-
defined settings are supported
To set the brightness
Standalone mode: to set any colour desired
DMX mode: to reduce the colour brightness
CH: number of DMX channels
A: DMX start address
To execute user-defined programs
Automatic show programs
P01 – P20, speed S00 – S31