Additional Setting Options; Reset To Factory Settings; Automatic Display Switch-Off; Key Lock - IMG STAGELINE ODB-1212RGBW Manual De Instrucciones

4.5 Additional setting options

4.5.1 Reset to factory settings

The factory settings of the unit are as fol-
lows:
Function
menu item
Show program
PROGRAM
Speed
PROGRAM
Number of DMX channels
DMXSETUP
DMX start address
DMXSETUP
Maximum colour bright-
ness
COLORSET
Total brightness
SETUPDIM
Shades of white
WHITE 11
Usage of subaddresses
SETUP ID
User-defined show pro-
grams
CUSTOM12
Behaviour in case of
control signal loss
DMX SIGN
Operating mode
RUN MODE
Display
SETUPDIS

Key lock

KEY LOCK
Signal control output
MASTER
‘
Factory settings
To reset, select the menu item
↵
press the button . The reset will take
approx. 30 seconds. Then the unit will go to
show program 1 (maximum speed).

4.5.2 Automatic display switch-off

1) Select the menu item
current setting will be indicated:
ON
Display illumination
switched on
OFF
Display illumination will switch off
after approx. 20 seconds if no but-
ton is pressed. When a button is
pressed, it will be switched on
again.
2) To change the setting, press the button
↵
: The current setting will start flashing.
3) Select the setting with the button
and then confirm with the button
indication will stop flashing.
14
4.5.3 Key lock
Activate the key lock to protect the unit
against unauthorized operation.
1) Select the menu item
2) Press the button
will start flashing:
Factory setting
OFF
10s
1
P:01
1
30s
S:01
3) Select the setting with the button
3
and then confirm with the button
CH03
indication will stop flashing.
1
A001
When a button is pressed, the message
HOLD FOR PRESS+/-
255
cate the key lock. For a brief unlock, press
the buttons
255
Key open
R G B W

4.5.4 Behaviour in case of control signal loss

W01
: 255, 220, 005, 227
W02
: 242, 222, 005, 227
When the light effect unit is controlled via a
W03
: 255, 255, 061, 255
DMX controller or when it is operated as a
W04
: 255, 255, 103, 255
slave unit in the master / slave mode, the
W05
: 255, 255, 130, 255
behaviour of the unit in case of control sig-
W06
: 255, 255, 138, 255
W07
: 255, 255, 153, 255 nal loss can be set:
W08
: 255, 255, 167, 255
1) Select the menu item
W09
: 255, 255, 180, 255
W10
: 255, 255, 185, 255
2) Press the button
W11
: 255, 255, 250, 255
will start flashing:
FREEZE
OFF
Reset will delete all
user-defined pro-
BLACKOUT
grams
3) Select the setting with the button
LEDs will "freeze"
and then confirm with the button
FREEZE
indication will stop flashing.
Slave mode
SLAVE

4.5.5 Reducing colour brightness

Always switched on
The maximum brightness possible of the
ON
colours red, green, blue and white can be
OFF
reduced. Thus, it is, for example, possible
to compensate differences to other light
ON
effect units and spotlights if they are con-
trolled together with the ODB-1212RGBW.
The setting will apply to both the stand-
RESET
and
alone mode and DMX control.
1) Select the menu item
2) Press the button
the brightness value of the primary
colour to be changed starts flashing
RED
(
SETUPDIS
. The
WHI
with the button
constantly
3) Confirm the setting with the button
The indication will stop flashing.
4) If required, repeat steps 2 and 3 for addi-
tional colours.
4.5.6 Indicating the internal temperature
To indicate the internal temperature, select
the menu item
Note: The LEDs will be dimmed when 65 °C are
L M exceeded.
or
↵
. The
To indicate the firmware version, select the
menu item
KEY LOCK
↵
: The current setting
No key lock
Buttons locked after 10 seconds if
no button is pressed
Buttons locked after 30 seconds
will appear to indi-
L M
and at the same time until
appears.
DMX SIGN
↵
: The current setting
"Freezing" of the LEDs with
the most recent control
command
LEDs off
COLORSET
↵
repeatedly until
GRE BLU
= red, = green,
= white). Set the colour brightness
L M
or .
and the firmware version
PCB TEMP
.
VERSION
.

5 Specifications

Data protocol: . . . . . . . . DMX 512
Number of
.
DMX channels: . . . . . . . 3, 4, 5, 8, 11 or 59
Light source: . . . . . . . . 12 RGBW LEDs
Power of each LED: . . 15 W
Beam angle: . . . . . . . . 10°
Power supply: . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . 185 VA max.
L M
or
Protective class
↵
. The
of housing: . . . . . . . . . . IP 65
Ambient temperature: . . -20 °C to +40 °C
Dimensions without
brackets (W × H × D): . . 1030 × 105 × 130 mm
Weight: . . . . . . . . . . . . . 10 kg
Accessories supplied: . . mains cable, 110 cm

5.1 DMX functions

Please note
The settings of the menu items
COLORSET
and
the DMX mode. The values set will define
.
the max. brightness possible (total bright-
ness and brightness for red, green, blue
and white). The easiest way to set the val-
ues to their maximum is to perform a reset.
5.1.1 Subaddresses for
11-channel / 59-channel mode
L M
or
DMX
↵
. The ID*
value
000 – 009 All
010 – 019 01
020 – 029 02
030 – 039 03
040 – 049 04
050 – 059 05
060 – 069 06
070 – 079 07
080 – 089 08
090 – 099 09
100 – 109 10
.
110 – 119 11
120 – 129 12
130 – 139 13
140 – 149 14
150 – 159 15
= blue,
160 – 169 16
170 – 179 17
180 – 189 18
↵
.
190 – 199 19
200 – 209 20
210 21
211 22
* ID = subaddress

5.1.2 3-channel mode

DMX
DMX value
channel
1 000 – 255
2 000 – 255
3 000 – 255
DMX cable, 70 cm
SETUPDIM
will also have an effect on
DMX DMX
ID* ID*
value value
212 23 234 45
213 24 235 46
214 25 236 47
215 26 237 48
216 27 238 49
217 28 239 50
218 29 240 51
219 30 241 52
220 31 242 53
221 32 243 54
222 33 244 55
223 34 245 56
224 35 246 57
225 36 247 58
226 37 248 59
227 38 249 60
228 39 250 61
229 40 251 62
230 41 252 63
231 42 253 64
232 43 254 65
233 44 255 66
Function
Shade of colour
Colour saturation
Brightness