Safety Regulations; Layout And Items Supplied - EINHELL TC-SM 2531/2 U Manual De Instrucciones Original

Sierra de tracción, oscilante y para cortar ingletes
Ocultar thumbs Ver también para TC-SM 2531/2 U:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 111
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Special information about the laser
Caution! Laser radiation
Do not look directly into the beam
Laser class 2
VORSICHT ! - LASERSTRAHLUNG !
Nicht in den Strahl blicken!
Laserspezifikation
Laser Klasse 2
: 650 nm; P
Never look directly into the laser path.
Never direct the laser beam at reflecting sur-
faces or persons or animals. Even a low out-
put laser beam can inflict injury on the eye.
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
Never open the laser module.
When the crosscut saw is not going to be
used for an extended period of time, the bat-
teries should be removed.
It is prohibited to carry out any modifications
to the laser to increase its power.
Anl_TC_SM_2531_2_U_SPK9.indb 21
Anl_TC_SM_2531_2_U_SPK9.indb 21
GB
0
- 21 -
The manufacturer cannot accept any liability
for damage due to non-observance of the
safety information.

2. Layout and items supplied

2.1 Layout (Fig. 1-17)
1. Handle
2. ON/OFF switch
3. Release button
4. Machine head
5. Saw shaft lock
6. Adjustable blade guard
7. Saw blade
8. Clamping device
9. Battery
10. Workpiece support
11. Fixed stop rail
12. Table insert
13. Hexagon key
14. Locking screw
15. Pointer
16. Scale
17. Turntable
18. Fixed saw table
19. Scale
20. Pointer
21. Locking screw
22. Sawdust bag
23. Drag guide
24. Locking screw for drag guide
25. Fastening bolt
26. Table width extension
27. Screw for cutting depth limiter
28. Stop for cutting depth limiter
29. Adjusting screw
30. Adjusting screw
31. Flange bolt
32. Outer fl ange
33. Lever
34. Movable stop rail
35. Laser
36. Locking screw for stop rail
37. ON/OFF switch for laser
38. Transport handle
39. Laser battery case
40. Battery compartment cover
a
round-head screw
b
spring washer
c
washer, small
d
nut
e
hex screw
f
washer, large
09.09.2019 15:00:03
09.09.2019 15:00:03

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

43.008.05Tc-sm 2531Tc-sm 2531 u

Tabla de contenido