Battery Disposal - EINHELL TC-SM 2531/2 U Manual De Instrucciones Original

Sierra de tracción, oscilante y para cortar ingletes
Ocultar thumbs Ver también para TC-SM 2531/2 U:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 111
5.5 and 5.6.
Cut as described under section 6.1.
6.5 Limiting the cutting depth (Fig. 3)
The cutting depth can be infinitely adjusted
using the screw (27). Turn the screw (27) in or
out to set the required cutting depth and then
retighten the knurled nut on the screw (27).
Check the setting by completing a test cut.
6.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means of
a zipper at the bottom (1).
6.7 Changing the saw blade (Fig. 1, 15-17)
Danger! Take the plug out of the socket to pre-
vent the machine starting up unintentionally.
Caution! Wear gloves to avoid getting cut when
changing the saw blade.
Using a hexagon head screwdriver, undo the
screw (41) on the machine head.
Push up the cover plate (42) to gain access to
the flange bolt.
Press the saw shaft lock (5) with one hand
while positioning the hexagon key (13) on the
flange bolt (31) with the other hand.
Firmly press on the saw shaft lock (5) and
slowly rotate the flange bolt (31) in the clock-
wise direction. The saw shaft lock (5) enga-
ges after no more than one rotation.
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
Turn the flange screw (31) completely out and
remove the external flange (32).
Take the blade (7) off the inner flange and pull
down and out.
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
Fit and fasten the new saw blade (7) in rever-
se order.
Push the cover plate (42) back into its starting
position and secure it with the screw (41).
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7), must coincide with the direc-
tion of the arrow on the housing.
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12) in both perpendicular and
Anl_TC_SM_2531_2_U_SPK9.indb 26
Anl_TC_SM_2531_2_U_SPK9.indb 26
GB
45° angle settings.
Important! Changing and aligning the saw
blade (7) must be carried out correctly.
6.8 Transport (Fig. 1-3)
Retighten the locking screw (14) to secure the
turntable (17) in place.
Activate the release lever (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
Fix the saw's drag function with the locking
screw for drag guide (24) in rear position.
Carry the equipment by the fixed saw table
(18).
To set up the equipment again, proceed as
described in section 5.2.
6.9 Operating the laser (Fig. 2)
Switching on: Move the On/Off switch (37) to
the "I" position to switch on the laser (35). A laser
line is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
Switching off : Move the On/Off switch (37) to the
"0" position.
Setting the laser: If necessary, slacken the
screws to adjust the laser. Retighten the screws
after you have made the adjustment. Important!
Never look directly into the laser beam!
Replacing the battery: Ensure that the laser
(35) is switched off . Remove the battery compart-
ment cover (40). Remove the old batteries and
replace with new ones (2 x 1.5 Volt R03, LR 03
Micro, AAA). Ensure correct polarity when inser-
ting the new batteries. Close the battery compart-
ment again.

6.10 Battery disposal

Recycle the packaging in an environmentally re-
sponsible manner. Sort the packaging for proper
recycling. The product may not be disposed of
with normal household refuse. Consumers have a
legal obligation to dispose of the batteries at the
appropriate collection points. Send your old bat-
teries to iSC GmbH, Eschenstrasse 6 in D-94405
Landau, Germany. You can then be sure that they
will be correctly disposed of by the manufacturer.
- 26 -
09.09.2019 15:00:05
09.09.2019 15:00:05

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

43.008.05Tc-sm 2531Tc-sm 2531 u

Tabla de contenido