Continuous Operation - EINHELL TE-DY 18 Li-Solo Manual De Instrucciones Original

If the battery pack fails to charge, please check:
•
whether there is voltage at the power socket,
and
•
whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, please send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
6.2 Changeover switch (Fig. 4 / item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the equipment is at a standstill.
When the slide switch is in the middle position,
the On/Off switch is blocked.
6.3 On/Off switch (Fig. 4 / item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you push in the
switch, the higher the speed of the cordless
screwdriver.
Switching on:
Press the On/Off switch (4).

Continuous operation:

Secure the ON/OFF switch (4) with the locking
button (5).
Switching off :
Press the On/Off switch (4) briefl y or release it.
6.4 Battery charge level indicator (Fig. 5 /Item
10)
Press the switch for the battery charge level indi-
cator (a). The battery charge level indicator (10)
uses 3 LEDs to show the charge status of the
battery.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty – you need to recharge the
battery.
Anl_TE_DY_18_Li_SPK9.indb 20 Anl_TE_DY_18_Li_SPK9.indb 20
GB
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective; it can no longer be used. Do not att-
empt to use or charge a defective battery pack.
6.5 LED light (Fig. 5 / item 9)
The LED light (9) can be used in poor lighting
conditions to illuminate the working area. The
LED light (9) will come on automatically as soon
as you press the On/Off switch (4).
6.6 Setting the screwing depth (Figure 6)
The depth setting ring (2) off ers latching settings
for pre-selecting the depth to which the screw is
screwed into the workpiece.
PLUS direction: Increased screwing depth
MINUS direction: Shorter screwing depth
The best way to establish the required depth set-
ting is to perform a screwing test.
Press the tip of the screw fi rmly against the ma-
terial in question until the screwing depth stop (1)
comes up against the workpiece and the coupling
disengages.
6.7 Changing the tool insert
To change the tool insert, rotate the screwing
depth stop (1) with the depth setting ring (2) to
the maximum screwing depth and pull off the tool
insert to the front (use pliers if necessary).
6.8 Screws
It is best to use self-centering screws (e.g. Torx,
cross recessed head), as these will enable you
to work safely and reliably. Always make sure that
the tool insert used is of the same size and shape
as the screw.
6.9 Removable holding clip (Fig. 1 / item 6)
When the holding clip (6) is mounted, the device
can be attached e.g. to a belt. The removable hol-
ding clip can be screwed either to the left or right-
hand side of the equipment. It is optional – it does
not need to be attached if you do not need it.
- 20 -
08.04.2019 15:42:42 08.04.2019 15:42:42