Introduction; Description Of The Equipment; Guarantee; Expiry Of Guarantee - GASPARDO PINOCCHIO ATTILA - ARTIGLIO Manual De Operación

1.0 INTRODUCTION

This booklet describes the regulations for use, maintenance for
seeding machine. This booklet is an integrating part of the product,
and must be kept in a safe place for consultation during the whole
life span of the machine.
The equipments described in these user instructions, corresponds
to the safety provisions and to state-of the-art techniques. However,
the risk of injury cannot be totally excluded especially when the
machine is not used properly. For this reason, the following pages
contain warning instructions with the following symbol.

1.1 DESCRIPTION OF THE EQUIPMENT

The work performed by this implement, known as to scarify, is
carried out at a greater depth than that usually applied.
The purpose of this implement is to reach deep into the earth,
moving the soil and enriching it with air, to break the furrow sole to
reach the deepest layers, thereby avoiding the damaging effect of
remixing it with the more superficial layers.
The scarifier are interchanging equipments capacities, with sturdy
straight chassis, in which the working organs constituted from an-
chors are fixed. It is especially suitable in loose soil and for preparing
the seedbed in cases in which the plough has not been used.
Its use us recommended in cases in which the earth is crumbly
enough to obtain clods of a size which allows the free passage of the
clods between the anchors without causing jamming. It is applied
to tractors equipped with third category three-point hook-ups.
ATTENTION
The equipment is suitable only for the use indicated. Any
other use different from that described in these instructions
could cause damage to the machine and represent a serious
hazard for the user.
Regular operation depends on the correct use and adequate main-
tenance of the equipment. It is advisable therefore to observe scru-
pulously what is described in order to prevent any inconveniences
that could prejudicate proper operation and duration.
cod. R19502010
ENGLISH
The equipment must be used, maintained and repaired by trained
personnel that have been instructed on the dangers arising from
its incorrect use. All the safety regulations and provisions for tech-
nical safety, occupational medicine and the Highway Code must
also be observed. The manufacture is not liable for any damage
to property or injury to persons due to modifications made to the
machine by the user.
It is just as important to keep to what is described in this booklet
since the Manufacturer declines all responsibility due to ne-
gligence and non-observance of these rules.
At any rate the Manufacturer is available to assure immediate and
accurate technical assistance and all that may be necessary for the
improved operation and better performance of the equipment.

1.2 GUARANTEE

- On delivery, check that the equipment has not been damaged
during transport and that the accessories are integral and com-
plete.
- Possible claims must be presented in writing within eight days
of receipt.
- The purchaser will enforce his rights on the guarantee only when
he has respected the conditions concerning the benefit of the
guarantee, set out in the supply contract.
- The guarantee is valid for 1 year, against all defects of material,
from the date of delivery of the equipment.
- The guarantee does not include working and shipping costs (the
material is shipped at the consignee's own risk).
- Obviously, all damage to persons or things are excluded from
the guarantee.
- The guarantee is limited to the repair or replacement of the defec-
tive piece, according to the instructions of the Manufacturer.
Dealers or users may not claim any indemnity from the Manufac-
turer for any damage they may suffer (costs for labor, transport,
defective workmanship, direct or indirect accidents, loss of earnings
on the harvest, etc.).

1.2.1 EXPIRY OF GUARANTEE

Besides what has already been set out in the supply contract,
the guarantee expires:
- If the limits set out in the technical data table are overshot.
- If the instructions set out in this booklet have not been carefully
followed.
- If the equipment is used badly, defective maintenance or other
errors by the client.
- If modifications have been carried out without written authorization
of the manufacturer and if non original spare parts have been
used.
25