HIKOKI DS 9DVF3 Instrucciones De Manejo página 10

English
c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
PRECAUTIONS FOR CORDLESS DRIVER DRILL
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
SPECIFICATIONS
POWER TOOL
Model
No-load speed (Low/High)
Wood
(Thickness 18 mm)
Drilling
Metal
(Thickness 1.6 mm)
Capacity
Machine screw
Driving
Wood screw
Rechargeable battery
Weight
10
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
4. Always charge the battery at a temperature of 10°C –
40°C. A temperature of less than 10°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature higher than 40°C.
The most suitable temperature for charging is that of
20°C – 25°C.
5. When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
Do not charge more than two batteries consecutively.
6. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
7. Never disassemble the rechargeable battery and
charger.
8. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the battery.
9. Do not dispose of the battery in fi re.
If the battery is burnt, it may explode.
10. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
11. Using an exhausted battery will damage the charger.
12. Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or infl ammables into the charger
air ventilation slots will result in electrical shock hazard or
damaged charger.
13. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
DS9DVF3
0 – 280 / 0 – 840 min
21 mm
Steel: 10 mm
6 mm
5.8 mm (diameter) × 45 mm (length)
(Requires a pilot hole)
EB912S: Ni-Cd 9.6 V (1.2 Ah 8 cells)
EB914S: Ni-Cd 9.6 V (1.4 Ah 8 cells)
BCC915: Ni-Cd 9.6 V (1.5 Ah 8 cells)
EB9B: Ni-Cd 9.6 V (2.0 Ah 8 cells)
1.4 kg
DS12DVF3
0 – 350 / 0 – 1050 min
-1
Steel: 12 mm
5.8 mm (diameter) × 63 mm (length)
(Requires a pilot hole)
EB1212S: Ni-Cd 12 V (1.2 Ah 10 cells)
EB1214S: Ni-Cd 12 V (1.4 Ah 10 cells)
BCC1215: Ni-Cd 12 V (1.5 Ah 10 cells)
EB1220BL: Ni-Cd 12 V (2.0 Ah 10 cells)
BCH1220: Ni-MH 12 V (2.0 Ah 10 cells)
-1
25 mm
6 mm
1.5 kg