Additional Safety Rules - Makita 9520NB Manual De Instrucciones

ENGLISH
1 Wheel guard
2 Bearing box
3 Screw
4 Lock nut
5 Depressed center wheel
SPECIFICATIONS
Model
Depressed center wheel diameter ................................... 100 mm
Spindle thread .................................................................. M10
-1
No load speed (min ) ...................................................... 12,000
Overall length ................................................................... 262 mm
Net weight ........................................................................ 1.3 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Always wear safety goggles and ear protec-
tors during operation.
2. Always be sure that the tool is switched off
and unplugged before carrying out any work
on the tool.
3. Keep guards in place.
4. Use only wheels with correct size and wheels
having a maximum operating speed at least as
high as the highest No Load Speed marked on
the tool's nameplate.When using depressed
center wheels, be sure to use only fiberglass-
reinforced wheels.
5. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
6. Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
7. Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
8. Use only flanges specified for this tool.
9. Do not damage the spindle, the flange (espe-
cially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
10. For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
Explanation of general view
6 Inner flange
7 Spindle
8 Lock nut wrench
9 Shaft lock
9520NB
11. Before using the tool on an actual workpiece,
12. Check that the workpiece is properly sup-
13. Hold the tool firmly.
14. Keep hands away from rotating parts.
15. Make sure the wheel is not contacting the
16. Use the specified surface of the wheel to
17. Do not use cutting off wheel for side grinding.
18. Watch out for flying sparks. Hold the tool so
ENB031-3
19. Pay attention that the wheel continues to
20. Do not touch the workpiece immediately after
21. Position the tool so that the power cord
22. If working place is extremely hot and humid, or
23. Do not use the tool on any materials contain-
24. Do not use water or grinding lubricant.
SAVE THESE INSTRUCTIONS.
10 Switch lever
11 Limit mark
12 Brush holder cap
13 Screwdriver
9521NB
115 mm
M14
12,000
262 mm
1.3 kg
test run the tool at the highest no load speed
for at least 30 seconds in a safe position. Stop
immediately if there is any vibration or wob-
bling that could indicate poor installation or a
poorly balanced wheel. Check the tool to
determine the cause.
ported.
workpiece before the switch is turned on.
perform the grinding.
that sparks fly away from you and other per-
sons or flammable materials.
rotate after the tool is switched off.
operation; it may be extremely hot and could
burn your skin.
always stays behind the tool during operation.
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure opera-
tor safety.
ing asbestos.
9522NB
125 mm
M14
9,500
262 mm
1.3 kg
5