Care & Maintenance; Troubleshooting Guide - Ninja BL642EU Manual De Usuario

Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
1 Separate/remove all parts from each other.
2 Hand Washing: Wash the containers, lids, blade
assemblies and attachments in warm, soapy water.
When washing the blade assemblies, use a dish-washing
utensil with a handle to avoid direct hand contact with
blades. Handle blade assemblies with care to avoid
contact with sharp edges. Rinse and air dry thoroughly.
Dishwasher: The containers, lids, blade assemblies
and attachments are all dishwasher safe. The lids
and Blade Assemblies are top rack dishwasher safe.
Ensure that the Blade Assemblies are removed from the
containers before placing in the dishwasher.
WARNING: Handle the Blade Assemblies with
care when washing, as the blades are sharp.
Contact with the blades' edges can result in
laceration.
3
Wipe the motor base clean with a damp cloth.
Please call customer service if any servicing needs to
be performed on the appliance at 0800 862 0453.
42
HOW TO STORE
|
1 Store the Nutri Ninja Ninja Blender Duo with
® ® ™
AUTO-iQ Technology upright with the blade assembly
™
inside the corresponding container with the lid secured
on top. Do not place anything on top. Store the rest
of the attachments in a safe place where they will not
be damaged and won't cause harm. Loosely wrap the
power cord around the motor base
NOTE: Do not store blended or unblended ingredients in
the Nutri Ninja cup with the blade assembly attached.
RESETTING THE MOTOR THERMOSTAT
Store the Nutri Ninja | Ninja Blender with Auto-iQ
® ®
Technology features a unique safety system which
prevents damage to the unit's motor and drive system
should you inadvertently overload your appliance. If
the appliance is being overloaded, the motor
will stop. Allow the appliance to cool for
approximately 15 minutes. To reset the appliance,
follow the resetting procedure below:
1
Unplug the appliance from the electrical outlet.
2
Remove and empty the container and ensure that no
food is jamming the blade assembly.
3 Allow the appliance to cool for approximately 15
minutes.
4
Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5 Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.

Troubleshooting Guide

PROBLEMS
Motor Doesn't Start or Blade
Assembly Doesn't Rotate.
®
Food is Unevenly Chopped.
Food is Chopped Too Fine or is
Too Watery.
Food Collects On Lid or On the
Sides of the Container.
You Cannot Achieve Snow
From Solid Ice.
Motor Base Won't Stick to
Counter or Table Top.
You get an "Err" Message.
You have a blinking red light.
POSSIBLE REASONS & SOLUTIONS
Make sure the container is securely locked into the motor base.
Make sure the lid is securely on container in the correct position (align arrows).
The appliance is turned "Off". Press the power button ( ) to turn "On".
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power light will flash.
Unplug and wait approximately 15 minutes before using again.
The unit has overheated. Unplug and wait approximately 15 minutes before using again.
Check to make sure the unit is not overloaded.
Either you are chopping too much food at one time, or the pieces are not of even
size and processing smaller amounts per batch.
The food has been over processed. Use Auto-iQ ® Pulse button for controlled
processing.
The mixture is too thick. Add more liquid.
Do not use ice that has been sitting out or has started to melt. Use ice straight
from the freezer.
Start with a few pulses and then go to a continuous blending cycle.
Make sure surface and suction feet are wiped clean. Suction feet will only stick to
smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood,
tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to a surface that
is not secure, (cutting board, platter, plates, etc.).
Your Ninja is able to detect which jar is on the base. You may be trying to use a
®
program that is not designed for the jar you have installed. The programs will light
up indicating which programs are available for each jar.
The unit is not installed properly. For your safety the unit will only be able to be
turned on when it is properly assembled. Please refer to the assembly pages of
this inspiration guide for assistance.
www.ninjakitchen.eu 43