Technical Data; Before Starting The Equipment - EINHELL TE-DW 18/225 Li Manual De Instrucciones

4. Technical data

Motor power supply: .................................... 18 V
Sanding surface ...................................Ø 225 mm
Idling speed ..................................600-1200 min
Telescopic tube ............................ 1100-1650 mm
Weight: ..........................................................3 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 86,8 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 97,8 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
Anl_TE-DW_18-225_Li_SPK9.indb 20 Anl_TE-DW_18-225_Li_SPK9.indb 20
-1
= 2.275 m/s
2
h
2
- 20 -
GB
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Danger!
The electric power tool generates an electro-
magnetic fi eld during operation. Under certain
circumstances this fi eld may actively or passively
impede medical implants. To reduce the risk of
serious or fatal injuries, we recommend persons
with medical implants to consult their doctor and
the manufacturer of the medical implant prior to
using the equipment.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Assembling the drywall sander (Fig. 2)
Take the drywall sander out of the packaging,
unfold it and secure with the locking hook (11).
Make sure that the locking hook (11) engages
correctly.
5.2 Fitting the telescopic extension (Fig. 3)
Insert the telescopic extension (4) into the ope-
ning (a) on the equipment and lock it with the
locking lever for the telescopic extension (3).
Note:
Adjust the drywall power sander with the telesco-
pic extension (4) so that you can work with it most
comfortably. Observe the „Max" mark on the tele-
scopic extension: This must not be exceeded.
06.07.2020 06:13:28 06.07.2020 06:13:28