Peg-Perego Booklet 50 Instrucciones De Uso página 15

For more information, consult our website:
www.pegperego.com
INSTRUCTIONS
1 OPENING: Before opening the frame, remove
(without using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER
BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY
HANDLE OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES
TO THIS FEATURE.
Press down the side fastener, hold the upper
section of the handle and rotate it towards
you until the frame is fully opened (fig_a).
Open frame (fig_b).
The frame is properly opened when the
attachment on the base clicks into place, as
shown.
2 FITTING THE WHEELS: Slot the uprights into
the rear wheel crosspiece (fig_a), ensuring
that it is facing the right way, then push the
rear wheels on and make sure that they click
into place (fig_b). To mount the front wheels,
fit them into the uprights until they lock into
place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
the figure (Fig_b).
To complete the operation, press the two
side buttons on the handle (Fig_c) to ensure
the handle pushes in all the way, until it clicks
into place (Fig_d).
4 BASKET ASSEMBLY: to facilitate basket
assembly, pull the tab outwards and lift as
shown in the figure (fig_a).
Slip the basket flap into the slot along the
front bar of the chassis (Fig_b).
5 Fasten the basket eyelets to the buttons on
each side of the frame.
6 To complete the basket attachment
procedure for the front part, you are required
to insert the supplied tie (fig_1) as follows:
position it between the basket and buttons,
as shown (fig_2) and use your finger to
push downwards, so as to complete the
attachment procedure (fig_3).
Repeat the same procedure for the other side
of the basket.
7 Attaching the rear part of the basket.
Remove the card from the rear bar.
Fasten the upper basket eyelet to the button
on each side of the frame (Fig_e).
Fasten the basket's two lower eyelets to the
two buttons on the rear bar of the frame
(Fig_f).
8 Basket fastened correctly (fig_g).
Lastly, re-position the footrest, pressing
inward with your hand as shown in the figure
(fig_h).
It is possible to increase the basket capacity
by pulling the tab outwards (fig_i).
WARNING! If you do not hook the basket on
correctly, as shown, the basket will be unable
to support the weight of loads placed in it.
9 HOOD: Fasten the back of the hood with the
Velcro strip (fig_a), insert the hood fasteners
into their slots (fig_b), secure to the buttons
inside the handlebar with the rubber band
(fig_c) and button the hood to the side of the
frame (fig_d).
10 Supplied with two parasol sections. To open,
pull forwards (fig_a).
The hood includes a loop to be used to hang
your child's favourite toy (fig_b). You can
detach the Velcro, roll up the back of the
hood and fasten it at the top with the rubber
band, so as to allow for greater ventilation
when using with the backrest down (fig_c).
11 FRONT BAR: insert the front bar as per the
sequence shown in the figure.
12 It can be adjusted into 2 positions:
POSITION 1: to use
POSITION 2: to attach the car seat
13 To remove the front bar, press down on the
buttons from both sides, as per the sequence
shown and remove (fig_a).
It is possible to open the front bar on one
side only, so as to facilitate the child's entry
and exit (fig_b).
WARNING: The front bar has not been
designed to support the child's weight; the
front bar has not been designed to lift the
seat with the child's weight. The front bar
does not replace the seat belt.
14 Before releasing the armrest, unfasten the
elastic from the cover on both sides.
15 Slightly close the chassis.
Rotate the armrest to unfasten it from the
cap, as shown in figure (fig.a).
To completely remove the armrest, pull it
outwards on both sides (fig.b).
Finally reattach the cover elastics to the
chassis.
16 Chassis without armrests. Keep the armrests
for a future use.
17 To reattach the armrests, proceed in reverse
sense. Pay attention to the attachment
direction.
When attaching the armrest, keep an eye on
the button, because it must be in front of the
armrest and not behind, as shown.
Attach the armrests to the chassis as shown.
18 FIXED OR SWIVELING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(fig_a) and lower them to allow the wheels to
swivel (fig_b). On uneven surfaces, the wheels
should be set to their fixed position.
19 BRAKE: Press the lever down to apply the
- 15 -