Tabla de contenido
Publicidad
3. SELECT A DESIRED TRACK BY PRESSING SKIP UP
4. PRESS THE" MEM/CLK-ADJ " BUTTON (12) TO STORE THE TRACK INTO MEMORY.
5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS "
DISC IN ASSIGNED ORDER.
6.
PRESS " STOP
" BUTTON (18) TO TERMINATE PROGRAM PLAY.
AFTER PROGRAM COMPLETE, PRESS "MEM/CLK-ADJ" BUTTON (12) REPEARTLY TO REVIEW THE
TRACKS BEING PROGRAMMED.
PRESS " STOP
FOR MP3 DISC / FILE, PRESS THE " FOLDER / PRE-UP " BUTTON (13) TO SELECT THE 1
OF NEXT FOLDER DIRECTLY AND HENCE TO SPEED UP THE SONG SELECTION.
THE PROGRAMMING MODEL WILL AUTOMATICALLY STOP IF NO BUTTON IS BEING PRESSED IN A
PERIOD OF ABOUT 10 SECONDS AFTER PRESSING THE " MEM/CLK-ADJ " BUTTON (12).
PLAYBACK OF MP3 SONG VIA USB STORAGE MEDIA
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 FILE WHICH STORED IN THE MEMORY MEDIA
WITH USB CONNECTING PORT.
1.
SET THE SYSTEM AT STANDBY MODE FIRST OR OTHER FUNCTION EXCEPT
USB MODE.
2.
PLUG-IN THE USB PEN-DRIVE WITH THE FACE UP & MAKE SURE IT GOING
INTO COMPLETELY. INSERT STRAIGHT WITHOUT BENDING.
CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD DAMAGE
THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB THUMB DRIVE).
CHECK TO BE SURE THE DIRECTION IS CORRECT BEFORE CONNECTION.
3.
PRESS FUNCTIONS BUTTON (11) TO SELECT "
4.
THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY
AFTER CONNECTING, AND LCD DISPLAY (2) WILL SHOW THE TOTAL
NUMBER OF MP3 FILES BEING DETECTED.
5.
REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE.
REMARK
-
THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 FORMAT ONLY THOUGH THE USB PORT.
-
IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3
ENCODING FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS
NOT A MAUFUNCTION OF THE SYSTEM.
-
USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED
FOR COMMUNICATION WITH COMPUTER DIRECTLY.
ENCODING OF CD/PHONO INTO MP3 FILE TO USB MEMORY
THE SYSTEM IS ABLE TO ENCODE NORMAL CD OR TURNTABLE TO MP3 FORMAT AND RECORDING AT
MEMORY MEDIA WITH USB CONNECTING PORT. BEFORE STARTING THE ENCODING, PLEASE INSERT THE
MEMORY MEDIA (USB PEN DRIVE) TO THE SYSTEM & MAKE SURE IT HAD ADEQUATE FREE MEMORY SIZE
FOR RECRODING:-
A) CD ENCODING
I) ECNODING 1 TRACK / 1 DISC
1.
PERFORM NORMAL PLAYBACK OF THE CD TRACK YOU WANT TO ENCODE & RECORD.
2.
PRESS "
WILL START ENCODING.
3.
THE SYSTEM WILL SHOW "
4.
PRESS THE "
RECORD ONE ENTIRE DISC " REC_ALL ".
5.
AFTER COMPLETING OF RECRODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
II) ENCODING BY PROGRAM
1.
PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO TRAY.
2.
SELECT THE DESIRE TRACKS BY FOLLOWING " CD DISC PROGRAMMING " PROCEDURES. THEN
PRESS " CD PLAY/PAUSE " BUTTON (16) TO START PLAYBACK..
3.
PRESS THE "
ENCODING IS NOW PERFORMING.
4.
PRESS THE "
" BUTTON (18) AT CD STOP MODE TO CANCEL ALL PROGRAMMED MEMORY.
" BUTTON (14) DURING THE PLAYBACK OF THE DESIRE TRACK AND THE SYSTEM
" & "
" BUTTON (14) REPEATLY AGAIN TO SELECT RECORD 1 TRACK " REC_ONE " OR
" BUTTON (14) AND THE UNIT WILL DISPLAY "
" BUTTON (14) REPEATLY AGAIN TO SELECT " REC_ALL ".
OR DOWN
" USB MODE.
" AND FLASHING. ENCODING IS PERFORMING NOW.
EN-5
BUTTONS (17/19).
" BUTTON (16) TO PLAY THE
" & "
" AND FLASHING.
ST
TRACK
Publicidad
Tabla de contenido
