Grounding Instructions - HoMedics Foot Salon Pro Manual De Instrucciones

Grounding Instructions

This product must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance
for the electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipment
grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and
Grounding Pin
grounded in accordance with all local codes and ordinances.
Figure A
DANGER
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are in
doubt as to whether the product is properly grounded.
Tab for Do not modify the plug provided with the product - if
Grounding
Adapter it will not fit the outlet, you may temporarily use an
Screw
adapter (such as the one shown in Figure B) until you
Figure B
have a proper outlet (such as the one shown in Figure C)
installed by a qualified electrician.
Grounded
Outlet
This product is for use on a nominal 120-volt circuit, and has
a grounding plug that looks like the plug illustrated in Figure
A. A temporary adapter that looks like the adapter illustrated
in Figure B may be used to connect this plug to a 2-pole
receptacle as shown in Figure D if a properly grounded outlet
Figure C
is not available. The temporary adapter should be used only
until a properly grounded outlet Figure C can be installed by
a qualified electrician. The tab for grounding screw Figure B
extending from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by a
metal screw. See Figures D and E.
Metal Screw
Figure D
Figure E
4
Foot Salon Pro Features
Caution:
To avoid injury
• Heat Boost Power heats water to warm spa temperature in minutes
and maintains temperature throughout use.
and irreparable
• Super quiet technology for total relaxation.
damage, always
• Pedicure center with 4 attachments–course pumice stone, gentle
remain seated
pumice stone, cleansing brush, and massage rollers.
• Convenient storage for attachments.
when using this
• Easy toe-touch controls to select bubbles, heat, vibration or a
footbath. Never
combination of these features.
stand on or in
• Raised nodes in floor manually massage feet.
the unit. • Massage rollers.
Instructions for Use
CAUTION: THIS
1. Ensure that the unit is unplugged before filling with water. Fill
UNIT CAN ONLY
with warm water to the fill line located on the inside of the tub.
RUN WITH
NOTE: Heat Boost will heat cold water and maintain the warm
water temperature. Heat boost will heat water to approximately
WATER IN IT.
98°F (37°C) in less than 15 minutes. Colder water will take longer
DO NOT USE
to warm up than warm water. For a quicker Heat Boost, fill with
warm water. Once water reaches optimal temperature, it will stay
WITHOUT
at this temperature for as long as heat function is selected. If
WATER.
water is too warm, turn heat off and let water cool down.
2. Plug the unit into a 120-volt household outlet.
3. Sit down in a comfortable position. With the touch of your
Note:
toe, select the feature you choose to use by pressing the
corresponding button. Press once to turn feature on. Press again
Heat Boost will
to turn feature off.
heat water to
a. Bubble Massage
b. Vibration Massage
approximately 98°
c. Heat.
F (37°C) in less
The red ring around the HEAT button will illuminate to indicate it
than 15 minutes.
has been selected.
Cold water will
Place your feet in the footbath. Press again to turn the feature
off.
take longer to
NOTE: Heat will only work if bubbles and/or vibration are
heat up than
selected.
warm water. For
4. To use the Pedicure Center:
a . Open storage compartment by pressing on the cover
quicker Heat
button. Select the desired attachment from the on-board
Boost, fill with
storage (Fig. 1)
warm water.
5