Grounding Instructions - HoMedics HAVEN MR-100 Manual Del Usuario

Grounding Instructions

This product must be grounded. If it should malfunction or break-
down, grounding provides a path of least resistance for the electric
current to reduce the risk of electric shock. This product is
Grounding Pin
equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropri-
Figure A
ate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
DANGER
Improper connection of the equipment-grounding conduc-
Tab for tor can result in a risk of electric shock. Check with a quali-
Grounding
Adapter
fied electrician or serviceman if you are in doubt as to
Screw
whether the product is properly grounded. Do not modify
Figure B
the plug provided with the product - if it will not fit the out-
let, you may temporarily use an adaptor (such as the one
Grounded
Outlet
shown in Figure B) until you have a proper outlet (such as
the one shown in Figure C) installed by a qualified electri-
cian.
This product is for use on a nominal 120-volt circuit, and has a
Figure C
grounding plug that looks like the plug illustrated in Figure A. A
temporary adapter that looks like the adapter illustrated in Figure
B may be used to connect this plug to a 2-pole receptacle as
shown in Figure D if a properly grounded outlet is not available.
The temporary adapter should be used only until a properly
grounded outlet Figure C can be installed by a qualified electri-
Metal Screw
cian. The tab for grounding screw Figure B extending from the
adapter must be connected to a permanent ground such as a
Figure D
properly grounded outlet box cover. Whenever the adapter is
used, it must be held in place by a metal screw. See Figures
D and E.
Caution — Please read all instructions carefully
before operating.
Figure E
• If you have any concerns regarding your health consult your
doctor before using this product.
• Those with the following conditions should consult their
physician prior to using this massage chair:
a) Malignant tumor
b) Heart Disease
c) Pregnancy
d) Conditions requiring rest
e) Back Disease or back trouble from an injury or accident.
f) Diabetes
• Individuals with pacemakers should consult a doctor before use.
• NEVER leave the appliance unattended, especially if children are
present.
• NEVER cover the appliance when it is in operation.
4
• DO NOT use this product for more than 20 minutes at a time.
• Extensive use could lead to the products excessive heating
and shorter life. Should this occur, discontinue use and allow
the unit to cool before operating.
• NEVER use this product directly on swollen or inflamed areas
or skin eruptions.
• This product is a non-professional appliance designed to
provide soothing massage to worn muscles. DO NOT use
this product as a substitute for medical attention.
• This product should NEVER be used by any individual suffering
from any physical ailment that would limit the user's capacity
to operate the controls.
• This product should never be used by any individual suffering
from any ailments that would limit or altogether inhibit the
user's capacity to feel or have any sensation in the body part
that the product is being used on.
• If you detect a malfunction or any other abnormal condition in
the operation of your chair, turn off the power immediately
and disconnect the power cord from the outlet.
• Should you have a power failure, turn the power switch to the
OFF position.
• If the chair has gotten wet or liquid is spilled near the main
power switch, turn the chair off, unplug it from the wall socket
and call HoMedics Consumer Relations.
• Do not use the massager while standing on a damp floor or
when any part of the body is in contact with plumbing or any
similar ground.
• Do not use unit if noise above normal sound is heard.
Assembly Instructions
Setting up your massage chair is easy to do. Your massage chair is
almost completely assembled. You will need two people to take the
chair out of the box, but the final assembly can be done by one
person. After carefully removing all the contents from the packag-
ing, inspect the chair and its components to make sure everything
has been received.
Components:
• Back cushion • Seat cushion
• Hand control • Softening pad
Step 1
Locate the red lever at the base of the back frame and press
inward to release the chair back from the folded position into an
upright position. The lever will align with the red knob attached to
the gas spring, which is located on the bottom of the chair seat.
You may need to lift the gas spring slightly to help the hinge connect.
Figure 1
5
• Head rest