Publicidad
Idiomas disponibles
Idiomas disponibles
Car radio connection
ISO plug in the vehicle
per.+12V
+12V
+12V/Kl15
1
Connection
1
In order to obtain full car radio output power and to avoid any
electrical wrong connections with ISO plugs installed in the car, the
car's ISO plug must not be directly connected to the car radio.
2
You can avoid making incorrect connections by using the vehicle-
specific Blaupunkt adapter wiring, but !
3
Due to the limited cross-section of the wiring in the vehicle, it is
necessary to use the connection cable 7 607 884 093 in addition to
the vehicle-specific Blaupunkt adapter wiring for the positive/
negative connection.
Be sure to observe Fig. 4, 5
When using the vehicle-specific adapter cable, cut off the radio's
connector and employ the connecting cable
7 607 884 093.
Advantage: The vehicle's wiring system is not damaged.
Positive connection
Connect the permanent +12 V lead (incl. anti-interference choke coil)
with the connecting cable 7 607 884 093 and attach directly to the
positive pole of the battery. Connect the illumination and antenna
leads and the ACC ignition lead (+12 V / terminal 15) to the
connecting cable as well.
Negative connection
Do not connect the negative lead to the negative pole of the battery!
Connect the negative cable with the connecting cable 7 607 884 093.
Lay the negative line to a suitable ground, such as a chassis screw or
the chassis itself. Cut the ground line as necessary
(do not form line loops).
The car radio is designed to be installed in the car radio compartment
provided by the vehicle manufacturer. Open the car radio compartment
(remove the shelf or panel by unclipping it) or adjust the size of the car
radio compartment to measure 182 x 53 mm.
For vehicles with deviating installation compartments, Blaupunkt offers
installation kits for 50 mm radio units for the most popular vehicle models.
Check the installation situation in the vehicle and, if necessary, use one
of the special installation kits for specific vehicle models,
e.g. Audi A4/A6/A8: 7 608 021 473
Note:
The mounting bracket included with this car radio is designed for
installation in vehicles with a standard DIN installation compartment
measuring 182 x 53 mm, 165 installation depth and an instrument panel
thickness of approximately 1 to 20 mm in the area of the tab fasteners,
see Fig. 1.
Reach behind the car radio compartment and check to see which tab
fasteners can be bent for the mounting bracket.
Note: Try to be sure to bend all of the tabs.
8 601 310 742
8 622 400 780
Car radio connection
with adapter wiring
2
182
165
53
1-20
Fig. 1
Car radio connection
with adapter and connection wiring
per.+12V
+12V
+12V/Kl15
GB
Place the mounting bracket in the compartment and bend over the tabs
with the help of a screwdriver, see Fig. 1, 2.
Connection, see page 4 or 5 or 6
Connection instructions ............................................................... Fig. 4
Positive/negative connection with vehicle-specific
adapter cable .............................................................................. Fig. 5
Positive/negative connection with connection line
7 607 884 093 ........................................................................... Fig. 5a
Equalizer or amplifier connection, (CINCH) ................................ Fig. 6
Do not connect the control wire to terminal 15 (+12 V switched) or
terminal 30 (permanent +12 V), maximum load < 150 mA.
Connection of 4 loudspeakers (4/35 W) ...................................... Fig. 7
LF = left front, RF = right front, LR = left rear, RR = right rear.
CD player connection CDC-F07 ................................................. Fig. 8
Connection of IR remote control RC-07 ...................................... Fig. 9
Use the connection cable attached to the remote control.
If necessary, also use cables 7 607 647 093 and 7 607 648 000.
Connection SUB-OUT(CINCH) ................................................. Fig. 10
Connection AUX L/R (CINCH) = 1 V ......................................... Fig. 11
Test microphone) ...................................................................... Fig. 12
The test microphone is used for the measurements of unwanted noise,
for the DNC cpntrol and for the HiFi and DNC calibration.
Connection in vehicles with QuickOut
In vehicles equipped with a QuickOut (currently Opel), the QuickOut unit
must be removed and the adapter cable used.
Installing the car radio
Place the car radio in the front of the mounting bracket and push it in until
the side springs snap into position on the left and the right (you will hear
an audible click).
Removing the car radio
Insert the handles into the holes in the panel on the left and right of the
radio and push them in until you hear a distinct click (unlocks side
springs).
Pull the unit out using both handles, see Fig. 3
Note: Handles which have snapped into place can only be
removed after you have pulled the radio out of the
compartment.
DNC (masking of driving noises)
For a description of the equaliser setting and the DNC calibration
process (masking of driving noises) please refer to the owner's manual.
This information is subject to change without notice!
Illustrations
Fig. 2
- 8 -
+12V
+12V
per.+12V
15A
3
7 607 884 093
12 V
8 601 910 002
1
2
2
Fig. 3
per.+12V
1
Publicidad
