Bosch GCM 10 S Professional Manual Original página 25

OBJ_BUCH-1126-005.book Page 25 Wednesday, April 27, 2016 3:07 PM
Technical Data
Sliding Mitre Saw
Article number 0 601 B20...
Rated power input
No-load speed
Weight according to
EPTA-Procedure 01:2014
Protection class
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Permissible workpiece dimensions (maximum/minimum) see page 28.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0,15 ohm.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 94 dB(A); Sound power level
105 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2 2
a <2,5 m/s , K=1,5 m/s .
h
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 61029 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards:
EN 61029-1, EN 61029-2-9, EN 50581.
Bosch Power Tools
... 503
... 508
... 532
... 542 ... 514
W 1800 1500
-1
min 4600 5000
kg 21.5 21.5
/II /II
mm 254 254
mm 1.4–2.5 1.4–2.5
mm 30 30
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Avoid unintentional starting of the machine. During
assembly and for all work on the machine, the power
plug must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the
accessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Locking knob 13
– Dust bag 1
– Material clamp 22
– Extraction adapter 27
– Hex key/cross-head screwdriver 30
– Ring/open-end spanner 35
... 534 ... 537 ... 541
1650 1800 1500
4700 4700 4300
21.5 21.5 21.5
/II /II /II
254 254 254
1.4–2.5 1.4–2.5 1.4–2.5
16 25.4 30
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 2N6 | (27.4.16)
English | 25
GCM 10 S
... 550
1800
4600
21.5
/II
254
1.4–2.5
25.4