SPARKY M 750 HD Compact Instrucciones De Uso página 8

cause injury beyond immediate area of op-
eration.
j) Hold the power tool by insulated grip-
ping surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own
cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the
power tool "live" and could give the opera-
tor an electric shock.
k) Position the cord clear of the spinning
accessory. If you lose control, the cord
may be cut or snagged and your hand or
arm may be pulled into the spinning acces-
sory.
l) Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the sur-
face and pull the power tool out of your con-
trol.
m) Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your cloth-
ing, pulling the accessory into your body.
n) Regularly clean the power tool's air
vents. The motor's fan will draw the dust
inside the housing and excessive accumu-
lation of powdered metal may cause electri-
cal hazards.
o) Do not operate the power tool near flam-
mable materials. Sparks could ignite these
materials.
p) Do not use accessories that require
liquid coolants. Using water or other liq-
uid coolants may result in electrocution or
shock.
▪ The tool must be used only for its pre-
scribed purpose. Any use other use
than those mentioned in this Instruction
will be considered a case of misuse. The
user and not the manufacturer shall be li-
able for any damage or injury resulting from
such cases of misuse.
▪ The manufacturer shall not be liable for
any changes made to the tool nor for any
damage resulting from such changes.
▪ When operating in dusty environment,
the ventilation slots must be kept clean.
If it should become necessary to clear
dust, first disconnect the tool from the
mains supply (use non metallic objects
to clean the dust) and avoid damaging
internal parts. The power tool will over-
heat under deteriorated cooling due to the
clogged with dust ventilation slots.
6
EN
further safety instructions for all opera-
tions
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the ac-
cessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/
or incorrect operating procedures or conditions
and can be avoided by taking proper precau-
tions as given below.
a) Maintain a firm grip on the power tool
and position your body and arm to al-
low you to resist kickback forces. Al-
ways use auxiliary handle, if provided,
for maximum control over kickback or
torque reaction during start-up. The
operator can control torque reactions or
kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over
your hand.
c) Do not position your body in the area
where power tool will move if kickback
occurs. Kickback will propel the tool in di-
rection opposite to the wheel's movement
at the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to
snag the rotating accessory and cause loss
of control or kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of con-
trol.
▪ Fix the machined piece in vice or in an-
other appropriate way.
M 750 HD Compact ● M 750E HD Compact