Working With The Machine - Festool KB-KA 65 Manual De Instrucciones

KB-KA 65
GB
Disassembly
Removal in reverse order.
Series production: When machining several
round workpieces with the same radius, the
trimming fixture with blade [1-5] can be set to the
same position for all edge bands.
Edge band trimming process (see chapter Trim-

ming edge bands on round workpieces).
Tighten the rotary knob [1-2] before trimming

the edge band.
The trimming fixture with blade [1-5] is now set
and secured in the same position for all edge
bands.
Edge band trimming process (see chapter Trim-

ming edge bands on round workpieces).
Tighten the rotary knob [1-2] before trimming

the edge band.
The trimming fixture with blade [1-5] is now set
and secured in the same position for all edge
bands.
4.6

Working with the machine

Trimming edge bands on rectangular workpieces
Fit stop pin [1-4] for square workpieces (see

chapter Fitting the stop pin for rectangular
workpieces [2]).
Slide the protruding edge band into the trim-

ming fixture with blade [1-5] [4].
Push the edge trimmer up to the stop pin [1-4]

parallel with the workpiece [4].
Push the handles [1-4] together and trim the

edge band [5].
Caution, sharp blade! Risk of injury! Keep
fingers well away from the blade on the trim-
ming fixture [1-5].
Trimming edge bands on round workpieces
Fit stop pin [1-4] for round workpieces (see

chapter Fitting the stop pin for round workpiec-
es [3]).
Glue the edge band to the workpiece.

Move the machine with the edge band away

from the workpiece approx. 10 cm in front of the
cutting point.
Apply glue up to the cutting point and leave

some space between the edge band and work-
piece so that the edge band is not glued to the
workpiece [6].
Mark the cutting point on the edge band [6 B].

Allow the protruding edge band to move over the

stop pin [1-4] and slide into the trimming fixture
with blade [1-5] [7].
10
Push the edge trimmer from the front towards

the workpiece up to the stop pin [1-4] until the
glued edge band makes contact with the inner
stop [1-7] [7].
Move the edge trimmer so that the mark is po-

sitioned approximately in the trimming fixture
with blade [1-5].
The fine adjuster for the edge length [1-3] can

be used to adjust the edge band with the mark-
ing more accurately [8].
The edge length scale [1-1] indicates whether
more or less of the edge band must be trimmed:
• Clockwise rotation: shorter edge band, more of
the edge band is trimmed -
• Anticlockwise rotation: longer edge band, less of
the edge band is trimmed +
If the marking is located directly behind the

blade on the trimming fixture [1-5], push the
handles [1-4] together and trim the edge band
[9].
Caution, sharp blade! Risk of injury! Keep
fingers well away from the blade on the trim-
ming fixture [1-5].
After trimming the workpiece, affix the edge

band with adhesive to the workpiece using a hot
air blower, for example.
4.7 Accessories
Trimming fixture with blade
The trimming fixture with blade [1-5] produces a
clean, accurate cut.
– Always use sharp, undamaged blades.
– Replace blunt or damaged blades.
Changing blades [10]
Slacken the screws using a cross-head screw-

driver [10-1].
Remove the blade [10-2].

Keep the shims in position [10-3].

Place the blade [10-2] over the shims [10-3].

Tighten the screws using a cross-head screw-

driver [10-1].
5 Edge magazine KSP-KA 65
Intended use
For the safe guidance of delicate and thin edging
into the edge bander KA 65.
Safe guidance of long edges without damaging or
soiling.
Max. edge lengths of 8 m (edge thickness of 2mm)
possible.
Easy machine guidance, even along long edges.