Hilti PS 38 Manual De Instrucciones página 29

12. FCC statement (US only)
-CAUTION-
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interfer-
en
ence in a residential installation. This equipment gener-
ates, uses, and can radiate radiofrequency energy and,
if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio com-
munications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment
on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Re-orient or re-locate the receiving antenna.
• Increase the distance between the equipment and
receiver.
• Connect the equipment to an outlet on a circuit differ-
ent from that to which the receiver is connected.
• Consult the dealer or an experienced TV/radio techni-
cian for assistance.
-NOTE-
Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference,
and
2) this device must accept any interference received,
including interference that may cause undesired
operation.
For US customers:
Operation of this device is restricted to law enforcement,
fire and rescue officials, scientific research institutes,
commercial mining companies, construction compa-
nies and private parties operating on behalf of these
groups. Operation by any other party is a violation of 47
U.S.C. § 301 and could subject the operator to serious
legal penalties.
Coordination Requirements
(a) UWB imaging systems require coordination through
the FCC before the equipment may be used. The oper-
ator shall comply with any constraints on equipment
usage resulting from this coordination.
(b) The users of UWB imaging devices shall supply
detailed operational areas to the FCC Office of Engi-
neering and Technology who shall coordinate this
information with the Federal Government through
the National Telecommunications and Information
Administration. The information provided by the UWB
operator shall include the name, address and other
pertinent contact information of the user, the desired
geographical area of operation, and the FCC ID num-
ber and other nomenclature of the UWB device. This
material shall be submitted to the following address:
Frequency Coordination Branch, OET
Federal Communications Commission
445 12th Street, SW
Washington, D.C. 20554
ATTN: UWB Coordination
(d) Users of authorized, coordinated UWB systems may
transfer them to other qualified users and to differ-
ent locations upon coordination of change of own-
ership or location to the FCC and coordination with
existing authorized operations.
(e) The NTIA/FCC coordination report shall include any
needed constraints that apply to day-to-day opera-
tions. Such constraints could specify prohibited areas
of operations or areas located near authorized radio
stations for which additional coordination is required
before operation of the UWB equipment. If additional
local coordination is required, a local coordination
contact will be provided. Ground Penetrating Radar
Coordination Notice And Equipment Registration.
Note: This form is only for Domestic United States
users. Failure to do this is a violation of Federal law.
1. Date:
2. Company name:
3. Address:
4. Contact Information [contact name and phone
number]:
5. Area Of Operation [state(s)]:
6. Equipment Identification
Brand Name: PS 38
FCC-ID: SDL-PS38R01
7. Receipt Date Of Equipment:
Fax this form to the FCC at: 202-418-1944 or
mail to:
Frequency Coordination Branch, OET
Federal Communications Commission
445 12th Street, SW
Washington, D.C. 20554
ATTN: UWB Coordination
Do not send this information to Hilti Corpora-
tion.