Quick ARIES FLAIR RIDER A 312 Manual Del Usuario página 17

POS. DESCRIPTION
15 Key
16 Key
17 Key
18A Chain guide cover A
18B Chain guide cover white F
18C Chain guide cover black F
19A Screw Aries
19B Screw Flair
20 Rope/chain stripper A-F base
21 Sensor
22 Screw for pressure lever
23A Black pressure lever
23B White pressure lever
24 Spring for pressure lever
25 Cover pin
26A Oval base Aries
26B Oval base white Flair
26C Oval base black Flair
27 Rope/chain stripper R base
28 Rider screw
29 Vite Rider
30 Gasket/ jig Aries-Flair-shaped
31 Gasket / jig Rider
32A Studs Aries base
32B Studs Flair base
33 Gearbox flange gasket
TOP TG40
34A Gearbox 500W Quick TG40 series MR0400000000
34B Gearbox "Hi Speed" 500W
Quick TG40 series
35 Washer
36 Spring washer
37 Nut
38 Screw
39 Paper gasket
40 Key
41A Electric motor 300W 12V
41B Electric motor 500W 12V
41C Electric motor 500W 24V
42 Flange gasket 500W
43 Watertight
44 Poles gasket
45 Bottom protec cover 500W
46 Screw
AFR 300/500W - REV011A
CODE
MBH0606025X0
MBH0606050X0
MBH0606060X0
Quick
SGMSGG040000
to marine environments. In any case, any salt deposits on
PDGC04DW0000
the outside must be removed periodically to avoid corrosion
PDGC04DB0000
and damage to the equipment. The parts where salt may
MBV0516MXSC0
have built up should be washed thoroughly with fresh water.
MBV0530MXSC0
MSN04VX00000
Once a year, the drum and the gypsy are to be taken apart
SAKREED00000
as follows:
MSMVT0400000
PDLVTD040000
DRUM VERSION
PDLVTD04W000
Use the handle (1) to loosen the bush (3); pull off the drum
MMTND0400000
(4) and the top clutch cone (5); loosen the fixing screws (19
MSR04X000000
or 29) of the rope/chain stripper (20 or 28) and remove it.
SGMSC04V0000
Pull off the gypsy (6).
SMPD04VW0000
SMPD04VB0000
NO-DRUM VERSION
SGMSC04C0000
Use the handle (1) to remove the gypsy cover (2); remove
MSN04CX00000
the top clutch cone (5); loosen the fixing screws (19 or 29) of
MBV0616MXTSC
the rope/chain stripper (20 or 28) and remove it and pull off
PGBSV0400000
the gypsy (6).
PGBSC0400000
MBP080607X00
Clean all the parts removed to avoid corrosion, and grease
MBP080608X00
the shaft thread (13 and 14) and the gypsy (6) where
the clutch cones (5) rest (use grease suitable for marine
PGFLRDTG4000
environment).
Periodically grease the hinge pin (25) of the inspection door
MR05AFHS0000
(only windlasses with aluminium bases).
MBR08X000000
MBR08XDE0000
Remove any oxide deposits from the terminals of the electric
MBD08MXEN000
motor and the reversing contactor unit; grease them.
MBV0516MXE00
PGBMR0400000
MBH040415F00
EMF031200000
EMF051200000
EMF052400000
PGGPMFN04000
PCCCPM040000
PGGPMPM04000
PCCPPMFN0400
MBV03916AXCC
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resistant
GB
17