Quick ARIES FLAIR RIDER A 712 Manual Del Usuario página 17

POS. DESCRIPTION
15 Key
16A Electric motor 700W 12V
16B Electric motor 700W 24V
16C Electric motor 1000W 12V
16D Electric motor 1000W 24V
16E Electric motor 1400W12V
16F Electric motor 1400W 24V
17 Gasket/Rider jig
18 Rider base
19 Sensor
20 Screw
21 Rope/chain stripper R base
22 Key
23 Short shaft
24 Long shaft
25 External circlip
26 Bearing
27 Internal circlip
28 Oil seal
29 Spring washer
30 Clutch cone
31 Magnet
32A Gypsy 6 mm
32B Gypsy 8 mm-5/16"
32C Gypsy 10 mm-3/8"
33 Gypsy cover
34 Drum
35 Bush
36A Handle 700/1000W
36B Handle 1400W
37 Screw for pressure lever
38A Black pressure lever
38B White pressure lever
39 Spring for gypsy pressure lever
40A Motor casing watertight 700W
40B Motor casing watertight 10/1400W PCCCPM100000
41 Grommet 1000/1400W
42 Terminal board cover
43 Screw
44 Bottom gasket
45 Bottom protec cover
46 Cable outlet
AFR 700/1000/1400W - REV008C
CODE
MBH050515F00
EMF071200000
EMF072400000
Quick
EMF101200000
ant to marine environments. In any case, any salt deposits
EMF102400000
on the outside must be removed periodically to avoid cor-
EMF141200000
rosion and damage to the equipment. The parts where salt
EMF142400000
may have built up should be washed thoroughly with fresh
PGBSC1000000
water.
SGMSC10C0000
KNREEDCL0000
Once a year, the drum and the gypsy are to be taken apart
MBV0620MXSC0
as follows:
MSN10CX00000
MBH080780F00
DRUM VERSION
MSAS10274R30
Use the handle (36) to loosen the bush (35); pull off the drum
MSAS10308R30
(34) and the top clutch cone (30); loosen the fixing screws (2
MBAE2520Y000
or 20) of the rope/chain stripper (3 or 21) and remove it. Pull
MBJ60052RS10
off the gypsy (32).
MBAN4717Y000
PGPRL2547700
NO-DRUM VERSION
MBR254025X00
Use the handle (36) to remove the gypsy cover (33); remove
MSF100000000
the top clutch cone (30); loosen the fixing screws (2 or 20) of
KPMC08060000
the rope/chain stripper (3 or 21) and remove it and pull off
ZSB100600000 the gypsy (32).
ZSB10 08516R4
Clean all the parts removed to avoid corrosion, and grease
ZSB1010380AR
the shaft thread (23 and 24) and the gypsy (32) where the
MSGB10000R01
clutch cones rest (use grease suitable for marine environ-
ZSGMSE100000
ment) (30).
MSD100000R01
MSHD00000000
Periodically grease the hinge pin (5) of the chain guide cover
ZSLMSH000000
(1) (only windlasses with aluminium bases).
MSMVT1000000
PDLVTD100000
Remove any oxide deposits from the terminals of the elec-
PDLVTD10W000
tric motor and the solenoid unit; grease them.
MMTND1000000
PCCCPM070000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17