Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CONNECTING WITH CLEANER
By connecting with cleaner (sold separately) through dust
collector and adapter (sold separately), most of dust can
be collected.
(1) Remove the hexagonal bar wrench from the base.
(2) Move the base fully forward. (Fig. 9, 10)
(3) Attach the chip cover.
(4) Connect the dust collector with adapter. (Fig. 16)
(5) Connect the adapter with the nose of cleaner. (Fig. 16)
(6) Insert dust collector into the rear hole of the base until
the hook catches in the notch. (Fig. 17)
(7) Press the hook to remove the dust collector.
NOTE
Wear the dust mask additionally, if available.
CONCERNING CUTTING OF STAINLESS STEEL
PLATES
CAUTION
In order to prevent blade dislodging, damage or excessive
wear on the Plunger, please make sure to have surface of
the base plate attached to the work piece while sawing.
When cutting stainless steel plates, adjust the unit as
described below:
1. Adjust the speed
Blade
Thickness of material
No. 97
1.5 – 2.5 mm
NOTE
Dial scale reading is for reference only. The higher the
speed is, the quicker the material is cut. But the service
life of the blade will be reduced in this case. When the
speed is too low, cutting will take longer, although the
service life will be prolonged. Make adjustments as
desired.
It is impossible for CJ110M to control the blade
operating speed.
Therefore do not cut stainless steel plate with CJ110M.
2. Set the orbital position to "0"
NOTE
When cutting use cutting fl uid (oil base cutting fl uid) to
prolong the blade's service life.
SELECTION OF BLADES
○ Accessory blades
To ensure maximum operating effi ciency and results, it
is very important to select the appropriate blade best
suited to the type and thickness of the material to be
cut. Three types of blades are provided as standard
accessories. The blade number is engraved in the
vicinity of the mounting portion of each blade. Select
appropriate blades by referring to Table 1.
HOUSING THE HEXAGONAL BAR WRENCH
It is possible to house the hexagonal bar wrench on the
base. (See Fig. 18)
Dial Scale
Middle groove position
between scales "2"
and "3"
MAINTENANCE AND INSPECTION
1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting effi ciency and may cause overloading
of the motor. Replace the blade with a new one as soon
as excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock
protection, carbon brush inspection and replacement
on this tool should ONLY be performed by a HiKOKI
Authorized Service Center.
5. Replacing supply cord
If the supply cord of Tool is damaged, the Tool must be
returned to HiKOKI Authorized Service Center for the
cord to be replaced.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modifi cation and inspection of HiKOKI Power
Tools must be carried out by an HiKOKI Authorized
Service Center.
This Parts List will be helpful if presented with the tool to
the HiKOKI Authorized Service Center when requesting
repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
HiKOKI Power Tools are constantly being improved
and modifi ed to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
English
8
Publicidad
Tabla de contenido
