Troubleshooting - Triton MOF 001 Instrucciones De Uso Y De Seguridad

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 34
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild
detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• To replace the brushes, remove the two Brush Access Covers (9). Remove the worn brushes
and ensure the sockets are clean. Carefully replace with new brushes and then replace the
Brush Access Covers
• After fitting run the router without load for 2-3 minutes to help the brushes bed in. The
process of the brushes fully bedding in may take repeated uses. Motor sparking may
continue until new carbon brushes have bedded in
• Alternatively, have the machine serviced at an authorised service centre

Troubleshooting

Problem
No function when Power Switch (12) is operated
Inaccurate cutting profile
Router will not operate
Router runs or cuts slowly
Excessive vibration
GB
Heavy sparking occurs inside motor housing
Micro Winder (10) "clicks" or not adjusting
Makes an unusual sound
8
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-GB/Support
Address:
Toolstream Ltd
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer
functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),
with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
Possible cause
No power
Defective On/Off Power Switch
Depth Stop (4) not correctly adjusted
Incorrectly fitted or loose router bit/Collet (22)
No supply of power
Brushes worn or sticking
Power Switch (12) is faulty
Motor components faulty or short circuited
Blunt or damaged cutter
Speed Controller (15) set low
Motor is overloaded
Incorrectly fitted or loose router bit
Bent or damaged router bit
Brushes not moving freely
Damaged or worn motor
Plunge Lock Lever (16) engaged
Reached end of adjustment range
Mechanical obstruction
Damage to internal windings
Solution
Check power supply
Replace the Power Switch at an authorised Triton service
centre
Ensure that the Depth Stop corresponds to the maximum
amount of cut permitted by the Turret Stops (1)
Tighten router bit/Collet and cutter assembly
Check that power is available at source
Disconnect power, open Brush Access Covers (9) and ensure
brushes are not damaged or heavily worn
Have the tool serviced by an authorised Triton service centre
Have the tool serviced by an authorised Triton service centre
Re-sharpen or replace cutter
Increase variable speed setting
Reduce pushing force on router
Refit or tighten router bit
Replace router bit
Disconnect power, remove brushes, clean or replace
Have the tool serviced by an authorised Triton service centre
Release Plunge Lock Lever (16)
Reset Micro Winder (10) and set depth with the Depth
Stop (4)
Have the tool serviced by an authorised Triton service centre
Have the tool serviced by an authorised Triton service centre

Publicidad

Tabla de contenido
loading

Tabla de contenido