Tabla de contenido
Publicidad
2. DESCRIPCIÓN
1.1 Bloque
1.2 Panel de mandos
Panel de mandos y diagrama del display (pantalla):
Funciones de los botones
2.1 ADJ: Botón de ajuste de la tempera-
tura: Para ajustar correctamente la tempe-
ratura del display con la temperatura que
es realmente.
2.2 SET: El botón SET se usa junto con los
selectores de aumento y disminución para
establecer la temperatura y tiempo reque-
ridos de funcionamiento.
2.3 START: Botón de funcionamiento:
Para empezar a trabajar
2.4 STOP: Botón de parada y pausa:
cuando se aprieta una sola vez, la máquina pausa; si se aprieta otra vez, el trabajo se para.
2.5
: Selector de aumento de la temperatura o el tiempo.
2.6
: Selector de disminución de la temperatura o el tiempo.
2.7
: Botón de movimiento hacia la derecha: Usado junto con el botón "ADJ" se ajus-
ta el error entre la temperatura real y la que se visualiza en el display.
2.8
: Botón de movimiento hacia la izquierda.
Pág. 4
Manual de instrucciones 50603010
CASTELLANO
1.3 Interruptor de encendido/apagado
1.4 Toma de corriente
1.5 Fusible
1.1
1.2
ENGLISH
1.3
1.5
2.5
THERMOBLOCK
MODEL 603/10
2.1
stop
adj
set
start
2.8
2.2
2.6
2.7
Revisión 1 Aril-08
If you are not using the equipment for a long period of time please make sure it is dis-
connected from the net and protected from dust (this way you will avoid accidents and
will extend its working-life).
Security
The dry bath must be used by previously qualified staff that knows how the equipment
works thanks to the user manual.
You should put the dry bath in a horizontal plane stable table, having a safety area of at
least 30 cm per side.
Do not place the equipment near any warm supply (burners, blowlamps, etc), nor
expose it directly to the sun. Avoid vibrations, dust and dry environments.
During its functioning dangerous materials such as flammable or pathological substan-
ces must be out of the safety area.
When you are not using the dry bath for a long period of time please make sure it is
unplugged in order to avoid possible accidents.
It is essential to have the equipment switched off and unplugged from the net before
cleaning, checking components or replacing any piece (e.g. replacement of a fuse).
Never try to repair the dry bath by yourself, since you will lose the warranty and may
1.4
provoke damages to the general operating system or the electrical installation, as well as
injuries to the people that usually handle the equipment (burns, hurts...).
Try not to spill any liquid on the control panel, though it is properly insulated. In case
you have any doubts do please immediately unplug the dry bath (see Maintenance).
Made under the European regulations for electrical security, electromagnetic compati-
bility and security on machines.
5. MAINTENANCE AND CLEANING
2.3
To get the best results and a higher duration of this equipment it is essential to follow
the processes of use.
2.4
Note: All the processes of use mentioned below will not have any value unless you keep
a continued and careful maintenance.
Please follow the processes of use of this manual.
This manual should be available for all users of this equipment.
Always use original components and supplies. Other devices can be similar but they
can damage the equipment.
The dry bath is supplied with a Schuko standard wire. It has to be plugged to an earth
connection and the socket should be handy and ready to unplug the equipment in case of
emergency.
Never try to repair the equipment by yourself, since you will lose the warranty and may
Version 1 April-08
Instruction manual 50603010
ENGLISH
Page 21
Publicidad
Tabla de contenido
