Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-PN 50 Manual De Instrucciones Original

6. Operation
6.1 Operation/Operating pressure
•
Connect the pneumatic stapler/nailer to the
compressed air connection (Fig.1/Item B).
•
Set the swivel air outlet (Fig.1/Item K) to the
desired position.
•
Before starting the stapler, switch on the com-
pressor and set the operating pressure on the
pressure reducer to 4 bar.
•
The knurled screw (Fig. 6/Item G) for precis-
ion adjustment must be approximately in the
middle position between Item 1 and 2. To do
so, turn open the knurled screw three revolu-
tions, starting from Position 1.
•
For the purpose of setting the operating
pressure it is advisable to use a test workpi-
ece which is similar in structure and material
thickness to the workpieces to be joined.
•
To staple/nail, place the pneumatic stapler/
nailer against the workpiece. Pull the trigger
lever (Fig. 1/Item A) once and release it again
after each shot.
•
If the nail or the staple goes in too deep, re-
duce the operating pressure on the pressure
reducer by 0.5 bar.
•
If the nail or the staple does not go in deep
enough or projects, increase the operating
pressure on the pressure reducer by 0.5 bar.
•
Place the stapler/nailer against the test work-
piece again and fire.
•
Depending on results, keep changing the
operating pressure in 0.5 bar increments until
the depth that the staples or nails are driven
in is roughly correct. For precision adjustment
(Section 6.2), use the knurled screw.
•
The equipment also has an automatic mode.
If you keep the trigger lever pressed, the stap-
les/nails will be shot automatically when the
pneumatic stapler/nailer is placed against the
workpiece.
•
To prevent faults, make sure that you do not
staple at the same point twice.
Danger!
If a staple or nail becomes jammed in the feed
shaft, always immediately depressurize the equip-
ment fi rst (remove the compressed air supply
hose), open the magazine shaft and only then re-
move the cover plates (Fig. 8/Item I/J) by undoing
the screws with the supplied hex key (Fig. 2/Item
N) (Fig. 7/8). Remove the jammed staples, clean
the shaft if necessary, and close again in reverse
order.
Anl_TC_PN_50_SPK9.indb 18 Anl_TC_PN_50_SPK9.indb 18
GB
6.2 Precision adjustment
•
The equipment has a depth setting adjuster
(Fig. 6/Item G) in the form of a knurled screw.
•
If you screw it downwards (Fig. 6/Item 1), the
staples/nails will be shot in deeper.
•
If you want to reduce the depth that the stap-
les/nails are shot in, you have to screw the
knurled screw upwards (Fig. 6/Item 2).
Danger! To prevent triggering unintentionally, the
depth setting must never be pulled back by hand
in normal operation.
7. Cleaning, maintenance and
ordering of spare parts
Disconnect the compressed air supply from the
equipment before performing any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment im-
mediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment.
7.2 Maintenance
Warning!
Disconnect the equipment from the compressed
air supply before you carry out any maintenance
or cleaning work.
Compliance with the maintenance instructions lis-
ted here will help this quality product provide you
with a long service life and trouble-free operation.
Regular lubrication is essential for your equip-
ment to work properly for a prolonged period of
time.
Regularly check the speed and the vibration level
by simply observing the tool.
Note: Use environmentally friendly compressed
air oil if you want to operate the equipment out-
side the workshop.
- 18 -
06.03.2019 10:14:21 06.03.2019 10:14:21