Transportation And Storage; Cleaning And Maintenance - Royal Catering RCWF-10LE-H Manual De Instrucciones

6. Once the machine is thoroughly cleaned, clip the cylinder back in its place (if it was removed). In order
to do this, place the cylinder on the two mounting pins and align it vertically so that it is in its original
position (in reverse order to that when it was removed).
7. Then fill the cylinder with foodstuffs and attach one of the funnels. To do that, unscrew the nut on the
discharge nozzle, select a funnel, align its wider end with the nozzle opening and attach the funnel to
the nozzle by tightening the nut.
8. Once the nozzle is fixed, gently tilt the cylinder and load it with foodstuffs.
9. Before connecting the machine to the power supply, make sure the cylinder is set to the correct,
vertical position, check that both switches are in the "0" position and that the knob is in the "Low"
position
10. There are two ways two lower the piston:
a. Using the foot pedal:
To lower the piston using the foot pedal, connect the foot pedal plug to the socket labelled with the
number 6 on the control panel (there is only one way to connect the plug to the socket). Then set the
switch on the left-hand side to "II", the switch under the potentiometer knob to "I" and press the foot
pedal. Use the potentiometer to adjust the piston operation rate (for faster operation turn the knob
clockwise towards the High setting, to slow it down or stop - anticlockwise towards the Low setting).
b. Without using the foot pedal:
To lower the piston without using the foot pedal, connect the short plug included in the set to the
socket labelled with the number 6 on the control panel (there is only one way to connect the plug to
the socket). Then set the switch on the left-hand side to "II" and the switch under the potentiometer
knob to "I ". Use the potentiometer to adjust the piston operation rate (for faster operation turn the
knob clockwise towards the High setting, to slow it down or stop - anticlockwise towards the Low
setting). In order to stop the piston, set the left and/or right switch to the "0" position (or turn the
knob anticlockwise as far as it will go).
11. The piston will stop once it reaches its lowest position.
12. To reverse the piston to the upper position, set the switch to "I" and wait for the piston to move up.
The machine will stop automatically.
13. To re-load foodstuffs into the cylinder, tilt it, insert the foodstuffs, re-align in the vertical position and
repeat the process in accordance with these instructions for as long as required.
14. After completion of the operation, set the piston to the upper position, set both switches to "0, turn
the knob to the "Low" setting and disconnect it from the power source.
15. Once the power source is disconnected, clean the machine with warm water and a soft cloth. The
electrical parts of the machine should not come into contact with water.
IX. TRANSPORTATION AND STORAGE
During transport, the machine should be protected from shaking, crashing and turning upside down. Store it
in a properly ventilated place with dry air and without any corrosive gas.
X. CLEANING AND MAINTENANCE
• Disconnect the machine from the electricity when cleaning it.
• Use cleaner without corrosive substances to clean surface.
• After cleaning, all parts should be able to dry before the machine is to be reused
• Store the unit in a dry, cool place, free from moisture and direct exposure to sunlight.
• Never spray the device with water jets.
12
XI. REGULAR CONTROL OF THE DEVICE
Check regularly whether the device is damaged. If it should be damaged, please stop using it immediately and
contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare the following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. The more detailed your information, the better the
customer service will be able to solve your problem rapidly and efficiently.
CAUTION: Never open the device without the authorization of your customer service. This can lead to a
loss of warranty!
XII. TROUBLESHOOTING
Symptoms
The piston moves down but no
stuffing comes out of the funnel
Rev. 21.01.2017
Rev. 21.01.2017
Possible reason Remedial actions
1. The funnel opening is too small Set the left-hand switch to the
2. The funnel opening is blocked "0" position immediately.
3. The foodstuffs is not sufficient- 1. Attach the funnel with a wider
ly ground opening
2. Move the piston to the upper
position, remove it and unclog
the blockage.
3. shred the food again
13