Installation Instructions; Warranty Card - SCHÜTTE SPIRAL Instrucciones De Montaje

Installation instructions

GB
Dear customer,
You have purchased a high-quality and long-lasting product
from our line of goods. Please read these instructions care-
fully before assembling and observe the notes.
Therefore, keep the instructions in a safe place and pass
them on to possible subsequent owners.
Safety notes
• Only allow experts carry out the installation work.
• CAUTION DAMAGE BY WATER!
Prior to installation please turn the general water supply
off.
• Ensure that all gaskets have the correct fit.
• These taps are not suitable for use on low pressure and
small electrical storage heaters.
• We recommend the installation of a filter into the appli-
ance or at least the use of angle valves with filter, in order
to avoid the inflow of foreign matter, which could damage
the cartridge.
• This tap is only intended for use in private households!
Only suitable for use in rooms with a temperature over 0 °C,
when there is danger of frost, sut off the water supply and
empty the tap.
• Take care when adjusting the warm water. Danger of
scalding!
• Incorrectly installed fittings can cause water damages!
• Please ensure that no caustic or corrosive products such as
detergents or household cleaning products make contact
with the connection hoses; this can lead to water damages.
• Despite careful production, sharp edges can occur. Please
exercise caution!
Disposal
Your washbasin tap is delivered in a solid packaging, in or-
der to protect it against transport damages. The packaging
consists of recyclable materials. Dispose it in an environ-
mentally suitable manner.
Do not throw the product into the normal domestic waste at
the end of its service life, but ask your municipal admini-
stration about the possibility of an environmentally friendly
disposal.
Technical data
• Flow pressure: Recommended as 1.5 to 6 bar; in case of
more than 6 bar connection pressure, we recommend that
a pressure reducer is installed
• Water temperature: max. 80 °C
Installation Instructions
• Only hand-screw the connecting pipes, do not use pliers
or a wrench!
• After installing the tap please unscrew the mixer nozzle,
flush the pipeline and the tap thoroughly for a longer time,
in order to flush out contaminations and residues.
• Do not twist or tension pipes! At first use check connec-
tions for leaktightness!
• Check all connections carefully after first-time use to make
sure that they are tight.
• We do not assume any warranty for incorrect installation -
in particular for subsequent damages!
Instructions for care
Sanitary taps require special care. Therefore, please observe
the following instructions:
• Chrome-plated surfaces are sensitive to lime-dissolving
agents, acidic cleaning agents and all kinds of abrasives.
• Never clean coloured surfaces with abrasive, corrosive, or
alcoholic agents.
• Only clean your taps with clear water and a soft cloth or a
shammy.
• Please make sure that no detergent is allowed to enter the
cartridge enclosure as this can cause the lever to become
stiff and cause noises.
Do not forget to unscrew the mixing nozzle in regular inter-
vals and to remove possibly calcareous residues or foreign
matter. It is advisable to replace the mixing nozzle with a
new one in the case of extreme contamination.
Maintenance
• Please note that a cartridge is an expendable part and that
the cartridge may need to be replaced every 1-2 years if
the water has high levels of limescale or dirt.
You will find illustrated instructions on how to replace the
cartridge on our website under the following link:
web.fjschuette.de/Austausch_Kartusche-Ventiloberteil.pdf
• Please check all joints and connections for leaks or visible
damages at regular intervals.
• In case of any leaks or visible damages to the fitting or
connection hoses, these should be immediately checked
by a specialist and replaced if necessary.
Decommissioning
• Cut off the water supply before dismantling the product.
• Pay attention to escaping residual water.
• Disassemble the product in the reverse order of the assem-
bly instructions.
 The illustrations are to be considered as figurative
representations, deviations of the product are possible.
Subject to technical modifications.

WARRANTY CARD

The Franz Joseph Schütte GmbH, based in Wallenhorst,
shall take on a manufacturer's warranty for the product you
have procured in accordance with the warranty conditions
stated below. Your legal warranty claims from the purchase
contract with the seller and your legal rights shall not be
limited by this warranty.
Warranty conditions:
1. Scope of warranty
The Franz Joseph Schütte GmbH shall grant a warranty
for proper material qualities and material processing in
accordance with the intended purpose as well as professi-
onal assembly, tightness and function. The warranty shall
only apply for the country in which the product has been
procured.
Included within the scope of the warranty is a guarantee, re-
duced to 1 year, for the durability of non-high-gloss chrome-
plated surfaces, such as bronzed or coloured surfaces.
8