Kenmore 66513463K900 Instrucciones De Instalación página 11

Lavavajillas ernpotrado
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Option 1, Countertop
attachment
The dishwasher
must
be secured
to the cabinet.There
are
two
brackets
on top of the
dishwasher
that
can be
brackets
attached
to the countertop
if it
is wood,
laminate
or another
similar
surface.
If your
countertop
is marble,
granite
or other
hard
surface,
these
brackets
will
not be used.
They
need
to be removed
and
discarded
front vent
NOTE:
Do not attach
the
model shown
dishwasher,
this
will
be done
later.
Option
2, Dishwasher
side attachment
for
marble
granite
or other
hard
surface
countertop
1.
Remove
the brackets
from
the top,
by flattening
tab at
back of brackets
with
pliers,
and pulling
the brackets
out of the slots.
/
tabs
2.
With
another
person
holding
the rear
of the dishwasher
to prevent
it from
tipping,
open
dishwasher
door,
and
place
towel
over
pump
assembly
and spray
arm
of
dishwasher.This
will
prevent
screws
from
falling
into
pump
area when
securing
dishwasher
to cabinet.
3.
Push the side
mount
bracket
into the slot on the side
of
dishwasher,
and bend
tab in towards
the side
of the
dishwasher
so that
it keeps
the bracket
in place.
Repeat
this step
for the other
side of the dishwasher.
NOTE:
Do not attach
the dishwasher,
this will
be done
later.
bend
i
tabs_
Move dishwasher
into cabinet
opening
1.
2.
3.
4.
5.
Using two or more people, stand the dishwasher
up.
Grasp the sides of the dishwasher
at the edges of the door panel.
Tilt dishwasher
backwards
on
wheels and move dishwasher
close
to cabinet opening.
Do not push on
the front of the panel or on the
console--they
may dent.
If dishwasher
has a power supply cord, insert power
supply cord into hole cut into cabinet.
If using direct wire, check that it is on the right front
side of opening.
Check that water line is on the left side of opening
and
drain hose is near the center of the hole in the cabinet.
6.
Slowly
move dishwasher
completely
into cabinet
opening.
Do not kink or pinch copper tubing,
drain
hose, power supply
cord or direct wire between
dishwasher
and cabinet.
HelpfulTip:
Once the dishwasher
is in position,
you
may have to support the front of the dishwasher
by
raising, lowering
or shimming
front feet.
Remove cardboard
from under dishwasher.
NOTE:
It is all right
if dishwasher
fits tightly
into
cabinet
opening.
Do not remove
insulation
blanket
--the
blanket
reduces
the sound
level.
Check
door spring
tension
With another
person
holding the dishwasher
to prevent it
from tipping,
open and close the door a few times.
If the
door closes or falls open under its own weight,
the door
tension will need to be adjusted.
• If the door closes too quickly, decrease the spring
tension
by moving
the spring end toward
the front of
the dishwasher.
• If the door falls open, increase the spring tension
by
moving the spring end toward the back of the
dishwasher.
• Springs should
be in the same notches on left and
right sides.
spring
move
spring end
10

Publicidad

Tabla de contenido
loading

Tabla de contenido