Standard Equipment; Brief Description; Dust Collection - Virutex SR165 Manual De Instrucciones

itand keep it close at hand, ready to carry out any inspection
of parts that may be necessary.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in thi this manual. Any other use
of the tool is strictly forbidden.
Before using the tool, make sure the mains voltage is co-
rrect, it must be the same as that on the specification label.
Machines with 230 V can also be connected to a 220 V
mains supply.
Before plugging in the tool, always make sure the control
switch K works properly and returns to the OFF position
when released.
4. PICTURES
DESCRIPTION (See pictures)
A) Saw blade (Fig. 1)
B) Riving knife setting screw (Fig. 1)
C) Mobile blade guard (Fig. 1)
D) Saw blade setting disc (Fig. 1)
E) Disc setting screw (Fig. 1)
F) Riving knife (Fig. 1)
G) Depth setting wing nut (Fig. 2)
H) Fence setting wing nut (Fig. 3)
I) Fence
J) Safety push button switch (Fig. 2)
K) On/Off switch (Fig. 2)
M) Angle setting wing nut (Fig. 3)
N) Sawdust extraction (Fig. 1)

5. STANDARD EQUIPMENT

- Fence
- Saw blade key
- Instructions manual and other documentation.

6. BRIEF DESCRIPTION

This tool is specially designed for straight sawing only
of boards made from wood and derivatives (plywood,
chipboard etc...).
7. START UP
Only plug in the machine when the switch
is in off position.
Press the locking button J, and squeeze the trigger in the
on/off switch K. When the on/off switch is released, the
machine stops.
8. FITTING THE SAW BLADE
Always unplug the machine before carrying
out any work on it.
CAUTION: Do not use bent or cracked blades or high-speed
steel blades. Do not use saw blades that do not conform to
the specifications contained in these instructions.
1. Move the mobile guard C backwards and hold it in place.
2. To loosen or tighten the screw E with the key supplied
with the machine, secure the blade shaft with the aid of
the push button P (Fig. 3).
3. Loosen the screw E and remove the setting disc D.
4. Fit the saw blade and tighten with the setting disc D
and the screw E.
5. Before fitting the new blade, make sure the surfaces in
contact with the setting discs are clean. The teeth of the
saw should protrude beyond the riving knife F. (The arrow
printed on the fixed guard of the machine indicates the
cutting direction of the teeth).
9. SETTINGS
1. Cutting depth setting
For a clean perfect cut, the cutting depth should be adjusted
to the thickness of the wood to be worked on, so that the
saw blade protrudes a tooth's height from the material. To
adjust the cutting depth, loosen the wing nut G and move
the machine upwards or downwards. The scale printed on
the parallel guide indicates the cutting depth.
2. Cutting angle setting
It can cut vertically and with an inclination of up to 45º.
The angle is adjusted by loosening the wing nut M and
according the scale printed on the base.
3. Riving knife adjustment
WARNING: The riving knife F prevents the blade from
seizing up duriing cutting operations and shold alwyas be
used for safety reasons.
The machine is supplied with the riving knife adjusted. When
fitting a new blade, follow the steps below for readjustment:
1. Raise the mobile guard C and loosen rhe screw button B.
2. Move the wedge through the slot to a distance from
the teeth tip and a cutting depth from same of 2 to 3 mm
(máx. 5 mm).
3. Tighten the screw B and the machine is ready to work.
4. Lateral fence adjustment
For parallel cutting, use the lateral fence I.
The cutting width is adjusted with the scale or according
to the plotting.
Tighten the wing nut H to work with the lateral fence.

10. DUST COLLECTION

Always make sure that the tool is switched
off and unplugged before fitting or removing
any dust extraction device.
Dust extraction keeps the workplace clean, prevents dust
build-up in the air and facilitates waste elimination.
These saws are equipped with a dust extraction hole N
to which the nozzle (optional accessory) 8204077 (Fig. 4)
11