Brevi TAZIO tt Manual De Instrucciones página 14

3.2 Adjusting the headrest in 5-point harness in-
stallation
A correctly adjusted headrest 07 ensures optimal protection for
your child in the safety seat: the headrest 07 must be adjusted
so that the shoulder belts 19 are at the same level as your child's
shoulders (fig. F3).
CAUTION! The shoulder belts 19 must not run behind the back of
the child or at ear height or above the ears.
The shoulder belts are adjusted as follows:
1. Press the adjusting button 26 and at the same time pull both shoul-
der belts 08 forwards. Do not pull on the shoulder pads 19, loosen the
5-point harness of the child seat as much as possible. (fig. F4)
Back side of the child seat:
2. Press the button of the shoulder belt height adjuster 10 at the
rear of the seat shell and tilt the shoulder belt height adjuster 10
towards you (fig. F5).
3. Slide the shoulder belt height adjuster 10 to select the correct
height of the shoulder belts 19 and engage it in the position that
fits for your child by releasing the button (fig. F5).
3.3. Adjusting the headrest in vehicle belt instal-
lation
A correctly adjusted headrest 07 ensures that the diagonal seat
belt section 11 is optimally positioned, and gives your child the
optimal protection.
The headrest 07 must be adjusted so that there is a space two
fingers wide between the headrest 07 and your child's shoulders.
(fig. F6)
To adjust the height of the headrest to fit your child:
1. Squeeze the adjustment handle 12 on the back of the headrest
07. This unlocks the headrest (fig. F7).
2. You can now move the unlocked headrest 07 to the desired
height. As soon as you release the adjustment handle 12 the he-
adrest 07 will lock into place.
3. If the position of headrest 07 is still not fix child, additional
adjustment can be made through the shoulder belt height adjuster
10, as explained in Section 3.2
4. INSTALLATION
4.1 Group 1 (9-18 kg) with isofix + top tether +
5-point harness
1. Make sure that the child seat's 5-point harness is installed cor-
rectly (see section 7).
2. Follow the steps in section 3.1 (to prepare the ISOFIX.)
3. Follow the steps in section 3.2 (to adjust headrest.)
4. Take the Top Tether and lay it over the child seat.
5. Place the child seat facing in the direction of travel on the ve-
hicle seat.
6. Grasp the child seat with both hands and slide the two locking
arms 15 firmly into the insert guides 02 until the locking arms en-
gage with a clicking noise on both sides, the ISOFIX indicator 04
turn green on both sides (fig. F8, F9).
CAUTION! The locking arms are only correctly engaged if both of
the safety buttons 04 are completely green.
7. Push the child seat towards the backrest applying firm, even
pressure on both sides (fig. F10).
14
534-01-161124-00 ISTRUZIONI SEGGIOLINO AUTO TAZIO TT.indd 14
8. Shake the child safety seat to make sure it is safely attached
and re-check the green safety buttons 04 to make sure that both
of them are completely green.
9.Take the top tether and if required, lengthen the belt by pressing
the top tether brake button to release the strap, pulling to adjust
as necessary (fig. F11).
10.Hook the snap hook 17 into the Top Tether anchoring point
recommended in your vehicle owner's guide. Look for this
symbol in your vehicle(fig. F12).
11. To tension the top tether, remove any slack by pulling on the
free end of strap until it is suitably tightened. The top tether will
be properly tightened when the tension indicator turns completely
green(fig. F13).
12. Follow the steps in section securing your child with 5-point
harness (see section 4)
4.1.1 Securing your child with 5-point harness
The more snugly the harness fits over your child's body, the better
your child will be protected. Therefore avoid putting thick clothes
on your child under the belt.
1. Open the harness buckle 21 by pressing red button (fig. F14).
2. Press the adjusting button 26 and at the same time pull both
shoulder belts forwards. Do not pull on the shoulder pads 19 (fig.
F14) .
3. Have your child sit down in the child seat.
4. Make sure that your child's back lies flat against the backrest
of the child seat.
5. Guide the two buckle latches 20 together and engage them
before putting them into the harness buckle 21 - this should make
a click noise (fig. F15, F16, F17).
6. Pull on the adjuster strap 09 until the harness lies flat and is
close against your child's body (fig. F18).
For the safety of your child, before every journey in the car check
that:
• the child safety seat is engaged on both sides with the ISOFIX
locking arms 15 in the ISOFIX attachment points 01 and that both
green safety buttons 04 are completely green (fig. F8)
• the child seat is firmly installed in the vehicle
• the Top Tether (fig. F13) is tightly tensioned over the backrest of
the car seat and the tension indicator is green
• the straps of the child safety seat are close to the body without
constricting the child
• the shoulder belts 08 are correctly adjusted and the straps are
not twisted
• the shoulder pads 19 are at the same level as your child's shoul-
ders (fig. F3)
• the buckle latches 20 are engaged in the harness buckle 21
(fig. F16)
4.2 Group 1 (9-18 kg) vehicle belt + 5-point har-
ness
1. Make sure that the child seat's 5-point harness is installed cor-
rectly (see section 7)
2. Follow the steps in section 3.2 (to adjust headrest)
3. Place the child seat facing in the direction of travel on the ve-
hicle seat
30/11/2016 15.29.41