Care And Maintenance; Care For The Harness Buckle - Brevi TAZIO tt Manual De Instrucciones

2. Press the button of the shoulder belt height adjuster 10 at the
rear of the seat shell and tilt the shoulder belt height adjuster 10
towards you (fig. F31).
3. Move the shoulder belt height adjuster 10 into the top position
and fix the position by releasing the button of the shoulder belt
height adjuster.
4. Loosen the 5-point harness of the child seat as much as pos-
sible. Unhook the shoulder belts 08 on the back side of the child
seat from the connecting piece 39 (fig. F32) .
5. Snap the connecting piece 39 in the provided storage (fig. F33)
6. Slide the belt loops off of the plastic extensions 41 of the shoul-
der belt height adjuster 10 (fig. F34).
Front side of the child seat:
7.Pull below both, the shoulder pads 19 and the two shoulder
belts 08 to the front through the slots 40 (front side of the child
seat) (fig. F35).
8. Open the harness buckle 21 (press the red release button) (fig. F36)
9. Open the left and right Velcro 42 on the lower part of the cover
43 and lift the cover piece to the front. Slide the buckle latches 20
down into the storage compartments (fig. F37).
10. Roll the shoulder belts 08 together and place them also into
the storage compartments (fig. F38).
11. Reposition the two cover parts to the rear and lock the Velcro
42 on the left and right side of the cover back side (fig. F39).
12. Lift the recline handle and pull at the front to fully recline the
child seat (fig. F40).
13. Grasp the metal plate 33 from underneath and turn it into a
vertical position.
14. Push upwards and slide the metal plate 33 through the slot 34.
Remove the harness buckle (fig. F41).
7.REFITTING THE 5-POINT HARNESS
1. Squeeze the adjustment handle 12 at the rear of the headrest
07 and push the headrest into the lowest position (fig. F42).
2. Open the left and right buttons Velcro on the lower part of the
cover 43 and lay the cover piece on the seating area (fig. F43).
3. Take the shoulder belts 08 and the buckle latches 20 from the
storage compartment 47 and unroll the shoulder belts (fig. F44).
4. Fold back the two cover pieces and close the left and right
poppers 42 on the lower part of the cover(fig. F45).
5. Refitting harness buckle 21 and crotch pad. Group 1 (9-18 kg)
use the belt slot closest to the backrest (a) ,for Group 2 (15-25 kg)
use the one furthest away (b) .
6. Take the harness buckle 21 and hold the metal plate 33 vertical-
ly. Push it with the narrow side upwards through the belt slot (a) or
(b) into the seat shell from above (fig. F46, F47).
7. Ensure by looking underneath the seat that the metal plate 33
is in a horizontal position and check the installation by pulling on
the harness buckle 21 several times(fig. F47).
8. Guide the two buckle latches 20 together and engage them
before putting them into the harness buckle 21 - this should make
a click noise (fig. F49).
CAUTION! The lap belts must not be twisted or swapped.
9. Thread the shoulder pads 19 onto the shoulder belts 08 in the
correct orientation as shown ensuring there are no twists. Align
the two loops of the shoulder belts 08 and strap loops of the
16
534-01-161124-00 ISTRUZIONI SEGGIOLINO AUTO TAZIO TT.indd 16
shoulder pads 19 (fig. F50) .
10. Pull the shoulder belts 08 and the strap loops of the shoulder
pads 19 through the slots 40 (fig. F51).
11. Pull the strap loops of the shoulder pads 19 onto the plastic
extensions 41 of the shoulder belt height adjuster 10 (fig. F52).
TIP
the strap loops of the shoulder pads should be the lower loop.
CAUTION! The shoulder belts 08 must not be twisted or swapped.
12. Take the connecting piece 39 from the provided storage on the
back side of the child seat.
13. Hook the shoulder belts 08 back onto the connecting piece 39.
The left loop on the left arm of the connecting piece and the right
loop on the right arm (fig. F53).

8. CARE AND MAINTENANCE

8.1 Care for the harness buckle

It is vital for the safety of your child that the harness buckle works
correctly.
Malfunctions of the harness buckle are usually caused by accu-
mulations of dirt or foreign bodies.
Malfunctions are as follows:
• The buckle latches are ejected only slowly when the red release
button is pressed.
• The buckle latches will no longer lock home (i.e. they are ejected
again if you try to push them in).
• The buckle latches engage without an audible "click".
• The buckle latches are difficult to insert (you feel resistance).
• The buckle only opens if extreme force is applied.
Remedy:
wash out the harness buckle so that it functions properly once
again
Cleaning the harness buckle
1.Follow section 6 to Remove the harness buckle 21 (fig. F54,
F55, F56, F57)
2.Soak the harness buckle 21 in warm water with light washing-up
liquid for at least an hour. Then rinse and dry it thoroughly.
8.2 Cleaning
The cover can be removed and washed. Please observe the in-
structions on the washing label of the cover.
Removing the cover
A) Headrest
1. Move the headrest of the child seat to the upper position (fig.
F58).
2. Take the elastic seam of the cover from the hooks at the back
side of the headrest (fig. F59) and remove the cover of the headrest.
B) Cover
1. Undo the hooks on the bottom side (fig. F60).
2. Remove the cover (fig. F61).
Re-fitting simply follow the steps in the opposite order.
9.WARRANTY
We guarantees its products against any manufacturer defect for a
period of 2 years, start from the day of purchase.
1. The warranty does not cover defects or failures caused by
30/11/2016 15.29.42