MIRKA DEOS 383X Instrucciones De Manejo página 11

Work stations
The tool is intended to be operated as a hand-held tool . It is always recommended that the tool should be used when
standing on a solid floor . It can be used in any position but before any such use, the operator must be in a secure
position have a firm grip and footing, and be aware that the sander can develop a torque reaction . See the section
"Operating instructions" .
How to get started
When unpacking the tool, make sure it is intact, complete and has not been damaged in transport . Never use a
damaged tool .
Before use, check that the backing pad is correctly mounted and tightened . Connect the power cord to the sander .
Connect the power cord to a grounded outlet (100–120 VAC, 50/60 Hz) .
In order to get the maximum power from this tool it is recommended to use it with the Mirka dust extractor and
Mirka Net Sanding products . The combination of Mirka sanders, net sanding products and Mirka dust extractor are the
basis of Mirka dust-free sanding solutions .
The power cord from the sander is connected to the mains supply on the front of the dust extractor . By connecting
the sander's power cord to the outlet on the dust extractor it is possible to use the dust extractor's autostart function .
Operating instructions
• The tool is intended to be operated as a hand-held tool . The tool can be used in any position . Note! The sander can
develop a torque reaction when started .
• Make sure the sander is switched off . Select a suitable abrasive and secure it to the backing pad . Make sure the
abrasive is centered on the backing pad . For optimal performance we recommend that this tool is used with other
Mirka products and accessories .
• Switch on the sander by pressing the On/Off key, Figure 1 . The sander LED (right) is now green .
• The sander can now be started by pressing the lever .
• The speed can be adjusted between 5,000 and max rpm by adjusting the position of the lever .
• The max rpm can be adjusted by pressing rpm+ or rpm–, Figure 1 . The rpm can be adjusted in steps 5,000, 6,000,
7,000, 7,500, 8,000, 9,000 and 10,000 rpm .
• The tool has two speed control modes . In the default mode the speed can be adjusted linearly by changing the
position of the lever . In the other mode the speed remains fixed at the set max rpm when the tool is running . When
the rpm+ and rpm– buttons are pressed simultaneously the tool toggles between the two controlling modes .
• When sanding, always place the tool on the work surface before starting the tool . Always remove the tool from the
work surface before stopping it .
• When sanding is finished, turn off the sander by pressing the On/Off key . The sander LED (right) is now turned off .
Bluetooth
This tool is equipped with Bluetooth® low energy technology and can be connected to an App from which additional
tool functionality can be accessed . For more information on the App functionality and whether it is available in your
country, go to www .mirka .com .
Activate Bluetooth on your Mirka® DEOS as follows:
1 . Connect the power cord to mains outlet .
2 . Press and hold the + button while switching the tool on with the On/Off button .
3 . Left LED lights up (green), to indicate that Bluetooth is active .
4 . Bluetooth is deactivated when the tool is disconnected form mains outlet .
NOTE! If the App is not installed or if it is not available in your country, Bluetooth should not be activated .
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc . and any use of such
marks by Mirka Ltd is under license . Other trademarks and trade names are those of their respective owners .
Compliance with the radio regulations in North America has been verified in accordance with FCC Part 15 subpart B
and C, RSS-GEN, RSS-247 and FCC §15 .247 .
Mirka® DEOS • 81 x 133 mm (3" x 5") & 70 x 198 mm (3" x 8")
en
11